Detailed instructions for use are in the User's Guide.
[. . . ] Traveler 3G
11n 3G Mobile Router
User's Manual
Copyright and Disclaimer
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user's guide. However, we are not liable for the inaccuracies or errors in this guide. All information is subject to change without notice All Trademarks are properties of their respective holders.
AirLive Traveler 3G User's Manual
Table of Contents
Table of Contents
1. [. . . ] Do not modify default value if you don't know how to configure it, default value is 100.
62
RTS Threshold
Beacon Interval
AirLive Traveler 3G User's Manual
6. General Setup
DTIM Period
Set the DTIM period of wireless radio. Do not modify default value if you don't know how to configure it, default value is 3. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it's not necessary to change this value unless you know what will happen after modification. Do not modify default value if you don't know how to configure it, default setting is "Auto 20/40 MHz". Do not modify default value if you don't know what it is, default setting is "Short Preamble". You can hide the ESSID of your wireless router (set the option to "Disable"), so only people those who know the ESSID of your wireless router can get connected. Enabling this setting will reduce the chance of radio signal collisions between 802. 11b and 802. 11g/n wireless access points. It's recommended to set this option to "Auto" or "Always". However, if you set to "None", your wireless router should be able to work fine, too. Unless you're using this wireless router in a really big space, you may not have to set output power to 100%. This will enhance security (malicious / unknown users in distance will not be able to reach your wireless router). The short of Wi-Fi MultiMedia, it will enhance the data transfer performance of multimedia contents when they're being transferred over wireless network. If you don't know how to configure it or you are not sure if you need it, it's safe to set this option to "Enable", and however, default value is "Disable".
Data Rate
N Data Rate Channel Width
Preamble Type
Broadcast ESSID
CTS Protect
Tx Power
WMM
After you finish Advanced Wireless Settings, please click "Apply" button, and the following message will be displayed on your web browser:
63
AirLive Traveler 3G User's Manual
6. General Setup
Please click "Continue" to back to previous setup menu; to continue on router setup, or click "Apply" to reboot the router so the settings will take effect (Please wait for about 60 seconds while router is rebooting).
6. 4. 3 Security Setting
It's very important to set wireless security settings properly!If you don't configure it, hackers and malicious users can reach your network and valuable data without your consent and this will cause serious security problem. To set wireless security settings, Please click "Wireless" menu on the left of web management interface, then click "Security Settings", then refer to the following instructions to set wireless security settings: Please select an encryption method from "Encryption" dropdown menu, there are four options:
6. 4. 3. 1 Disable wireless security When you select this mode, data encryption is disabled, and every wireless device in proximity will be able to connect your wireless router if no other security measure is enabled.
Only use this option when you really want to allow everyone to use your wireless router, and you don't care someone else can read the data without your consent.
AirLive Traveler 3G User's Manual
64
6. General Setup
6. 4. 3. 2 WEP - Wired Equivalent Privacy When you select this mode, the wireless router will use WEP encryption, and the following setup menu will be shown on your web browser:
Key Length
There are two types of WEP key length: 64-bit and 128-bit. Using "128-bit" is safer than "64-bit", but will reduce some data transfer performance. When you select a key format, the number of characters of key will be displayed. For example, if you select "64-bit" as key length, and "Hex" as key format, you'll see the message at the right of "Key Format" is Hex (10 characters), which means the length of WEP key is 10 characters. You can configure up to four sets of WEP key, and you can decide which key is being used by default here. [. . . ] For example, if the IP address for a device is, in its binary form, 11011001. 10110000. 10010000. 00000111, and if its network mask is, 11111111. 11111111. 11110000. 00000000 It means the device's network address is 11011001. 10110000. 10010000. 00000000, and its host ID is, 00000000. 00000000. 00000000. 00000111. This is a convenient and efficient method for routers to route IP packets to their destination.
ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet router located at the ISP's office.
ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations.
LAN: Local Area Network. [. . . ]