User manual AIRLIVE VOIP-440S

[. . . ] WAN VLAN Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAC Spoofing Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LAN Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DHCP Server Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Multicast Limits: Broadcast Limit: the value specifies the maximum limit on the percentage of broadcast packets which will be bridged to the destination interface (as a percentage of the source side bandwidth) 4 Multicast Limit: the value specifies the maximum limit on the percentage of multicast packets which will be bridged to the destination interface (as a percentage of the source side bandwidth) 5 WAN PPPoE Configuration 1. Enable PPPoE: "Yes" or "No", to enable/disable PPPoE 2. Under "Authentication", you enter the username and password given by your ISP. Settings: Idle Timeout: Idle timeout before PPP connection is closed due to inactivity Echo Timeout: the duration between PPP echo requests sending to server. Echo Count: the number of unanswered PPP echo requests before PPP connection is closed. Service Name: PPPoE Service name AC Name: PPPoE AC name 6 IPSec Configuration This page allows configuration of the device's IPSec (IP Security) settings. Enable tunnel 1: Enable/disable tunnel 1 IP sec Remote IP Address range: start and end of remote IP address range. Remote security gateway: Remote security gateway IP address Security Mode: IPSec mode (tunneling/transport) Outbound AH SPI (DEC): Outbound AH security parameter index number. Outbound AH Authentication Algorithm: in HMAC-MD5 or HMAC-SHA1 Outbound AH Authentication Key (HEX): hex number up to 40 nibbles Outbound ESP SPI (DEC): Outbound ESP security parameter index number Outbound ESP Encryption Algorithm: in 3DES-CBC or DES-CBC Outbound ESP Authentication Algorithm: in HMAC-MD5 or HMAC-SHA1 Outbound ESP Encryption Key (HEX): hex number up to 48 nibbles Outbound ESP Authentication Key (HEX): hex number up to 40 nibbles Inbound AH SPI (DEC): Inbound AH security parameter index number Inbound AH Authentication Algorithm: in HMAC-MD5 or HMAC-SHA1 7 Inbound AH Authentication Key (HEX): hex number up to 40 nibbles Inbound ESP SPI (DEC): Inbound ESP security parameter index number Inbound ESP Encryption Algorithm: 3DES-CBC or DES-CBC Inbound ESP Authentication Algorithm: in HMAC-MD5 or HMAC-SHA1 Inbound ESP Encryption Key (HEX): hex number up to 48 nibbles Inbound ESP Authentication Key (HEX): hex number up to 40 nibbles 8 WAN VLAN Configuration WAN VLAN Tag: VLAN tag for all outgoing packets on interface. The value should be between 0 and 4094 WAN Priority Tag: Priority tag for all outgoing packets on interface. The value should be between 0 and 7 9 MAC Spoofing Configuration WAN MAC Address (Spoofed): Only available when devices under the router mode. The spoofed MAC address to be used by the device's WAN interfaces, the Ethernet address of the outgoing packets from the WAN interface would be replaced with this address. If blank, the WAN interfaces will use the value of MAC 10 LAN LAN Configuration 1. Under "Network Settings", you enter the IP address and subnet mask of your network. Multicast Limits: Broadcast Limit: the value specifies the maximum limit on the percentage of broadcast packets which will be bridged to the destination interface (as a percentage of the source side bandwidth) Multicast Limit: the value specifies the maximum limit on the percentage of multicast packets which will be bridged to the destination interface (as a percentage of the source side bandwidth) 11 DHCP Server Configuration These configuration parameters are for the device's internal DHCP server. Server Setting: "Yes" or "No", to enable/disable DHCP Client IP Address Range: Minimum and Maximum limit on the DHCP IP address pool 2. Client Network Information Domain Name: LAN domain name provided to DHCP clients during the OFFER process. DNS Server: This statically assigned DNS server IP address will be provided to clients during the OFFER process. Static Address Assignment Up to eight static DHCP address assignments can be configured. To add a static IP assignment, enter the LAN device's host name (must be unique in the private network) and/or MAC address. Specify the Internal address to be assigned and press the "Add" button. 12 Router Configuration These configuration parameters are for the device's internal router. Dynamic Routing: Whether or not dynamic routing on TX/RX interfaces is enabled/disabled. [. . . ] Regardless of the above syntax a timer is only allowed if it appears in the last position in a string (12T3 is not valid). The unit will process the dial plan by comparing the current dial string against the dial plan, if the result is underqualified (partial matches at least one entry) then it will do nothing further. If the result matches or is over-qualified (no further digits could possibly produce a match) then send the string to the gatekeeper and clear the dial string. The Timer T is activated when it is all that is required to produce a match. [. . . ]