User manual AIRLIVE WN-350R

[. . . ] Copyright & Disclaimer WN-350R Wireless b/g/n 2T2R 300 Mbps Router User's Manual WN-350R User's Manual 1 Copyright & Disclaimer Copyright Copyright ©2010/2011 by this company. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. [. . . ] Setup Procedure for `AP Bridge-Point to Multi-Point' In this mode, you can connect your wireless router with at least four wireless routers to expand the scope of wireless network, and all clients (wired only ­ AP will not accept wireless clients in this mode) of the wireless routers will think they're on the same physical network. 1 2 3 4 5 6 7 8 Here are descriptions of every setup items: Band (2): Select the band you want to use; all the wireless routers must use the same setting. Channel Number (3): Select the channel you want to use, all the wireless routers must use the same setting. MAC address 1 to 4 (4 - 7): Security Setting (8): Click to set security settings for this connection (Please go to section `2-7-3 Wireless Security' for detailed instructions). Input the MAC address of other wireless routers. WN-350R User's Manual 84 2. Setup Procedure for `AP Bridge ­ WDS' In this mode, you can expand the scope of network by combining up to four other access points together, and every access point can still accept wireless clients. NOTE: For WDS mode, the output signal nature is the same as that of normal AP mode. 1 2 3 4 5 6 7 8 9 10 Here are descriptions of every setup items: Band (2): Select the band you want to use, all the wireless routers must use the same setting. SSID (3): Input the SSID of your wireless router, the setting should be the same with other wireless routers for the convenience of roaming. 85 WN-350R User's Manual 2. System and Network Setup Channel Number (4): Select the channel you want to use, all the wireless routers must use the same setting. Associated Clients (5):Click `Show Active Clients' button, then an "Active Wireless Client Table" will pop up. You can see the status of all active wireless stations that are connecting to the access point. MAC address 1 to 4 (6 - 9): Security Setting (10): Click to set security settings for this connection (Please go to section `2-7-3 Wireless Security' for detailed instructions). Setup Procedure for `Universal Repeater' In this mode, the router can act as a wireless repeater; it can be Station and AP at the same time. It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage. NOTE: For Repeater Mode, this router will demodulate the received signal, checking if this signal is noise for the operating network then have the signal modulated and amplified again. The output power of this mode is the same as that of WDS and normal AP mode. WN-350R User's Manual 86 2. System and Network Setup 1 2 3 4 5 6 7 Here are descriptions of every setup items: Band (2): Select the band you want to use, all the wireless routers must use the same setting. You can type any alphanumerical characters here, maximum 32 characters. SSID is used to identify your own wireless router from others when there are other wireless routers in the same area. Default SSID is `default', it's recommended to change default ESSID value to the one which is meaningful to you, like myhome, office_room1, etc. ChannelNumber (4): Select the channel you want to use, all the wireless clients must use the same setting. Associated Clients (5): Click `Show Active Clients' button, then an "Active Wireless Client Table" will pop up. You can see the status of all active wireless stations that are connecting to the access point. 87 WN-350R User's Manual 2. System and Network Setup Root AP SSID (6): In `Universal Repeater' mode, this device can act as a station to connect to a Root AP. You should assign the SSID of the Root AP here or click `Select Site Survey' button to choose a Root AP. Site Survey (7): Click `Select Site Survey' button, then a "Wireless Site Survey Table" will pop up. [. . . ] This is a convenient and efficient method for routers to route IP packets to their destination. WN-350R User's Manual 164 4. The ISP Gateway Address is an IP address for the Internet router located at the ISP's office. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). [. . . ]