User manual APPLIED ENERGY DX180

[. . . ] · A ceiling or wall on/off switch with built in indicator (DX180T/DX180H) If installing in a wall (surface mounting) 1. Use this centre to cut an opening through the wall Ø117mm, with a slight fall to the exterior. Fit the wall tube (not supplied) and mortar into place. If mounting in a wall (flush mounting) The surround 10 is not required. Fit the ducting to the circular spigot 6. ) User adjustments . Guarantee e Before making any adjustments, isolate the fan completely from the mains supply, check specification below to see which features apply to your fan. [. . . ] Drill 4 pilot holes into the ceiling through the hole of each clip, ensuring not to damage the clip, and fit the clips ensuring correct alignment. Pass the electrical cable into the fan box 5 through the front cable inlet hole. Using suitable screws 11 (Fig. B), fix the fan box flange to the ceiling clips. · The humidity setting is adjustable between approximately 50% and 90% relative humidity. Use an electrician's screwdriver, and turn screw "RH" (Fig. D), clockwise to increase the relative humidity setting and anti-clockwise to decrease. (Note: the fan is more sensitive at 50% RH than at 90% and is factory set at approximately 70%). Premier DX180H Also at the address below Using the fan Premier DX180 Operate the fan using the external on/off switch. . Head Office ­ UK Sales Office and Spares Applied Energy Products Ltd, Morley Way, Peterborough, PE2 9JJ, England Tel: +44 (0) 1733 456789 Fax: +44 (0) 1733 310606 Sales/Spares Hotline: +44 (0) 8709 000420 Sales/Spares Faxline: +44 (0) 8709 000520 Web: http://www. xpelair. co. uk s Premier DX180T Operate the fan using the external on/off switch. When the switch is turned off, the fan continues to operate for the over-run timer period. (Fixed at approximately 20 minutes). International Guarantee ­ Contact your local distributor or Xpelair direct s Premier DX180H . IMPORTANT · READ ALL THESE INSTRUCTIONS & WARNINGS FULLY BEFORE COMMENCING INSTALLATION. · INSTALLATIONS AND WIRING MUST CONFORM TO CURRENT IEE REGULATIONS (UK), LOCAL OR APPROPRIATE REGULATIONS (OTHER COUNTRIES). IT IS THE INSTALLER'S RESPONSIBILTY TO ENSURE THAT THE APPROPRIATE BUILDING CODES OF PRACTICE ARE ADHERED TO. · THESE APPLIANCES ARE INTENDED FOR CONNECTION TO FIXED WIRING · CHECK THAT THE ELECTRICAL RATING SHOWN ON THE FAN MATCHES THE MAINS SUPPLY. · SITE AWAY FROM DIRECT SOURCES OF HEAT (I. E. : GAS COOKERS OR EYE-LEVEL GRILLS) AND NOT WHERE AMBIENT TEMPERATURES ARE LIKELY TO EXCEED 50 OC. · WHEN THE FAN IS INSTALLED IN A ROOM CONTAINING A FUEL BURNING APPLIANCE, PRECAUTIONS MUST BE TAKEN TO AVOID THE BACKFLOW OF GASES INTO THE ROOM FROM THE OPEN FLUE OF THE FUEL BURNING APPLIANCE · ENSURE THAT ALL RELEVANT SAFETY PRECAUTIONS (CORRECT EYE PROTECTION AND PROTECTIVE CLOTHING ETC) ARE TAKEN WHEN INSTALLING, OPERATING AND MAINTAINING THIS FAN. · IF ANY SECTION OF THE DUCTWORK IS POSITIONED HIGHER THAN THE FAN A CONDENSATION TRAP (XCT100) MUST BE FITTED AS CLOSE AS POSSIBLE TO THE FAN · GENERAL GUIDANCE FOR SITING THE FAN SEE "FIG. G". ALWAYS SITE FAN AS HIGH AS POSSIBLE · THE APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS. YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THEY DO NOT PLAY WITH THE APPLIANCE If installing in a ceiling (flush mounting) For Ø100mm ducting: 1. For flat ducting: · This fan can be installed within a 47mm void without the circular spigot 6 (Fig. E). Flat ducting adapter (FDA) available. ) Terminating the ducting Fit an outer grille to the outer wall. For ceiling mounting, use appropriate ancillaries. g s Wire the electrical connections WARNING: THIS APPLIANCE MUST BE EARTHED Switched Operation The fan can be wired with a separate on/off switch. [. . . ] For fixed wiring circuits, the protective fuse for the appliance must not exceed 5A. For Australia Only Permanently connected to the supply and a remote switch controls operation. They should be directly wired to the supply through an approved 10A wall mounted surface switch with at least 3mm clearance between contacts. Cleaning 1. Only clean the external surface of the fan, using a damp lint free cloth. [. . . ]