User manual APRILIA ETV 1000 CAPONORD

[. . . ] We have drawn up this booklet to provide a comprehensive overview of your vehicle's quality features. Please, read it carefully before riding the vehicle for the first time. it contains information , tips and precautions for using your vehicle. It also describes features, details and devices to assure you that you have made the right choice. [. . . ] Following the instructions, ask the passenger (if any) to get onto and then get off the vehicle. Catalytic models are fitted with a silencer with a "two-way platinum-rhodium" catalytic converter. This device oxidises CO (carbon monoxide) and HC (unburned hydrocarbons) present in exhaust fumes, turning them into carbon dioxide and water vapour respectively. Vehicle owners are warned that the law may prohibit the following: - the removal of any device or element belonging to a new vehicle or any other action by anyone leading to render it nonoperating, if not for maintenance, repair or replacement reasons, in order to control noise emission before the sale or de- Livery of the vehicle to the ultimate buyer or while it is used; - using the vehicle after that device or element has been removed or rendered non-operating. Check the muffler/exhaust silencer and the silencer pipes, make sure there are no signs of rust or holes and that the exhaust system works properly. If exhaust noise increases, take your vehicle to an Official aprilia Dealer at once. There are two stands in the vehicle: - side stand (3); - OPTIONAL centre stand The stand has two positions: - normal or retracted (home position); 03_25 - extended (working position). If the stand has been retracted for any manoeuvre (for example, when the vehicle is in motion), rest the vehicle on its stand again as follows: CAUTION 03_26 MAKE SURE THE GROUND WHERE YOU HAVE PARKED IS EMPTY, FIRM AND LEVEL. Check that the stand (3) does not present any backlash at all whether extended or retracted. extend the stand (3) from its retracted position and check that the springs (4) fully extend the stand. Fold the stand (3) up again and release it half way checking if the springs (4) make the stand retract completely. A safety switch (5) is installed on the side stand (3) to inhibit ignition or to stop the engine when a gear is engaged and the side stand (3) is lowered. A) and keep the engine at idle, then operate the clutch lever (7) fully. Push down the side stand (3) which will activate the safety switch (5). At this stage: - the engine should stop; - on the instrument panel the "side stand down" warning LED should be on. NEVER leave the ignition key inserted in the lock and always use the steering lock. Write down your personal details and telephone number on this page to help identifying the owner in case of vehicle retrieval after a theft. 03_31 Strictly follow the instructions compiled below in order to avoid injuring people, damaging property, things and the vehicle in the event the rider or the passenger falls off the vehicle and/or the vehicle falls or overturns. When getting on and off the vehicle, make sure nothing is restricting your movements; do not hold any objects in your hands (helmet, gloves or goggles not put on). Always get on and off the vehicle on the left side and with the side stand lowered. The stand has been designed to support the weight of the vehicle and a minimum load, without the added weight of rider and passenger. 03_33 The purpose of the side stand is to prevent the vehicle from falling or overturning while rider and passenger get on the vehicle and get ready to ride; the stand should not be used to support the weight of rider and passenger. [. . . ] Engine revs at idle speed Clutch 1200 +/- 100 rpm Multiple disks, oil-bath clutch with hydraulic control on the left side of the handlebar and PPC device Dry sump system with separate oil tank and cooling radiator Type Mechanical, 6 speeds with foot lever on the left hand side of the engine Type Type endless (without master link) and with sealed links 525 Model Type Type twin-spar frame with die-cast elements made of light alloy and moulded extrusions 28° 129 mm (5. 89 in) light alloy oscillating fork with differentiated arm profiles and adjustable hydropneumatic single shock absorber 120 mm (4. Type - front (standard) Type - front (alternative) PIRELLI / SCORPION S/T MT90 METZELER / TOURANCE BRIDGESTONE / TRIAL WING 101 RADIAL F. Low-beam/high-beam lights (halogen) Front tail light Turn indicator lights Rear tail light /stop light License plate light 12 V - 60 / 55 W H4 V 12V - 3W 12 V - 21 W 12 V - 5 / 21 W 12V - 5W Gear in neutral Turn indicators Fuel reserve High-beam light Stand down Engine oil pressure Diagnosis LED LED LED LED LED LED LED 023 in) single socket boxspanner (4); - extension for single socket box-spanners (5); - 6 - 7 mm (0. [. . . ]