User manual ASROCK P4 COMBO
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ASROCK P4 COMBO. We hope that this ASROCK P4 COMBO user guide will be useful to you.
Manual abstract: user guide ASROCK P4 COMBO
Detailed instructions for use are in the User's Guide.
[. . . ] P4 Combo
User Manual
Version 1. 0 Published July 2004 Copyright©2004 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. 31)
1_2
Default Setting
Note: The default setting of the FSB Select jumper is shorting pin1 and pin2. Please keep the default setting for the system's stability.
18
2. 7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
FDD connector
(33-pin FLOPPY1) (see p. 8 No. 20)
Pin1 FLOPPY1
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. 10)
PIN1
IDE1
PIN1
IDE2
connect the black end connect the blue end to the IDE devices to the motherboard 80-conductor ATA 66/100 cable Note: If you use only one IDE device on this motherboard, please set the IDE device as "Master". Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). 17)
SATA2
SATA1
These two Serial ATA (SATA) connectors support SATA data cables for internal storage devices. Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard.
Serial ATA (SATA) Data Cable
19
Serial ATA (SATA) Power Cable
(Optional)
connect to the SATA HDD power connector connect to the power supply
Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. This USB4_5 connector is shared with the USB 2. 0 ports 4, 5 on ASRock I/O PlusTM. When using the front panel USB ports by attaching the front panel USB cable to this connector (USB4_5), the USB ports 4, 5 on ASRock I/O PlusTM will not be able to function. This header supports an optional wireless transmitting and receiving infrared module. These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices.
USB 2. 0 Header
(9-pin USB67) (see p. 8 No. 19)
1
USB_PWR P-6 P+6 GND DUMMY
GND P+7 P-7 USB_PWR
Shared USB 2. 0 Header
(9-pin USB4_5) (see p. 8 No. 32)
1 USB_PWR P-4 P+4 GND USB_PWR P-5 P+5 GND DUMMY
Infrared Module Header
(5-pin IR1) (see p. 8 No. 29)
1
IRTX +5V DUMMY
GND IRRX
Internal Audio Connectors
(4-pin CD1, 4-pin AUX1) (CD1: see p. 8 No. 26)
CD-R GND GND CD-L
AUX-R GND GND AUX-L
CD1
AUX1
Front Panel Audio Header
(9-pin AUDIO1) (see p. 8 No. [. . . ] OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it. Configuration options: [Disabled], [300], and [330].
33
3. 3. 8 USB Configuration
BIOS SETUP UTILITY Advanced USB Configuration
USB Devices Enabled : None USB Controller USB 2. 0 Support Legacy USB Support [Enabled] [Enabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit To enable or disable the onboard USB controllers.
+F1 F9 F10 ESC
v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc.
USB Controller Use this item to enable or disable the use of USB controller. USB 2. 0 Support Use this item to enable or disable the USB 2. 0 support. Legacy USB Support Use this item to enable or disable the support to emulate legacy I/O devices such as mouse, keyboard, . . . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ASROCK P4 COMBO
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ASROCK P4 COMBO will begin.