User manual ASROCK P4S61

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ASROCK P4S61. We hope that this ASROCK P4S61 user guide will be useful to you.


ASROCK P4S61 : Download the complete user guide (727 Ko)

Manual abstract: user guide ASROCK P4S61

Detailed instructions for use are in the User's Guide.

[. . . ] P4S61 User Manual Version 1. 0 Published October 2003 Copyright©2003 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Connect the fan cable to the connector matching the black wire to the ground pin. Connect an ATX power supply to the connector. Chassis fan connector (3-pin CHA_FAN1) (see p. 7 item 14) GND +12V CHA_FAN_SPEED CPU fan connector (3-pin CPU_FAN1) (see p. 7 item 5) GND +12V CPU_FAN_SPEED ATX power connector (20-pin ATXPWR1) (see p. 7 item 2) Serial port connector (9-pin COM1) (see p. 7 item 20) 1 RRXD1 DDTR#1 DDSR#1 CCTS#1 This COM1 connector supports a serial port module. RRI#1 RRTS#1 GND TTXD1 DDCD#1 15 Chapter 3 BIOS Setup 3. 1 BIOS Setup Utility This section explains how to configure your system using the BIOS Setup Utility. When you start up the computer, there is a chance for you to run the BIOS Setup. Press <F2> during the Power-On-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST continues with its test routines. If you wish to enter the BIOS Setup after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. It is a menu-driven program, which allows you to scroll through its various sub-menus and select among the predetermined choices. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and may not exactly match what you see on your screen. 3. 1. 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Sets up the basic system configuration ADVANCED Sets up the advanced features SECURITY Sets up the security features POWER Configures Power Management features BOOT Configures the default system device that is used to locate and load the Operating System EXIT Exits the current menu or the BIOS Setup To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted. 3. 1. 2 Legend Bar At the bottom of the Setup Screen is a legend bar. The following table lists the keys in the legend bar with their corresponding functions. 16 Navigation Key(s) <F1> <ESC> / / +/<Enter> <F9> <F10> Function Description Displays the General Help Screen Jumps to the Exit menu or returns to the upper menu from the current menu Moves cursor up or down between fields Selects menu to the left or right Increases or decreases values Brings up a selected menu for a highlighted field Loads all the setup items to default value Saves changes and exits Setup 3. 2 Main Menu When you enter the BIOS Setup Utility, the following screen appears. Main Advanced Security AMIBIOS SETUP UTILITY - VERSION 3. 31a Boot Power Exit [ System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DDR1 DDR2 DDR3 Setup Help ] Oct 17 2003 Fri 20:07:40 Month: Jan - Dec Day: 01 - 31 Year: 1980 - 2099 P4S61 BIOS P1. 00 Pentium (R) 4 CPU 2400 MHz 512 KB F29 / 11 224 MB + 32 MB Share Memory 256 MB / 166 MHz (DDR333) None None F1:Help Esc:Exit :Select Item :Select Menu +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit System Date [Month/Day/Year] Set the system date that you specify. Valid values for month, day, and year are Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). System Time [Hour:Minute:Second] Set the system to the time that you specify. IDE Devices Use this to configure IDE devices. 17 TYPE To set the type of the IDE device, first, please select "IDE Devices" on Main menu and press <Enter> to get into the sub-menu. Then, select among "Primary IDE Master", "Primary IDE Slave", "Secondary IDE Master", and "Secondary IDE Slave" to make configuration of its type. Below are the configuration options. AMIBIOS SETUP UTILITY - VERSION 3. 31a Main Primary IDE Master: [ Auto Setup Help ] Type Cylinders Heads Write Precompensation Sectors Maximum Capacity LBA Mode Block Mode Fast Programmed I/O Modes 32 Bit Transfer Mode Ultra DMA Mode Select how to set the parameters of drive, Or Select [AUTO] to set all HDD parameters automatically. On On Auto On Auto F1:Help Esc:Previous Menu :Select Item +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit [USER]: It allows user to manually enter the number of cylinders, heads, and sectors per track for the drive. Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk. If autodetection is successful, the BIOS Setup automatically fills in the correct values for the remaining fields on this sub-menu. If the autodetection fails, it may due to that the hard disk is too old or too new. If the hard disk was already formatted on an older system, the BIOS Setup may detect incorrect parameters. In these cases, select [User] to manually enter the IDE hard disk drive parameters. After entering the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active. 18 [CD/DVD]: This is used for IDE CD/DVD drives. [. . . ] Power Setup Menu Main Advanced Security AMIBIOS SETUP UTILITY - VERSION 3. 31a Boot Power Exit [ Setup Help ] Suspend To RAM (S3) Repost Video on S3 Resume Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second Disabled Disabled Power Off Disabled Disabled Disabled Disabled Every Day 12 30 00 Set the power state after an unexpected AC / Power loss. F1:Help Esc:Exit :Select Item :Select Menu +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit Suspend to RAM (S3): This field allows you to select whether to auto-detect or disable the ACPI Suspend-to-RAM (S3) feature. Repost Video on S3 Resume: This feature allows you to repost video on S3 resume. It is recommended to enable this feature under Microsoft® Windows® 98 / ME. Restore on AC/Power Loss: This allows you to set the power state after an unexpected AC/Power loss. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ASROCK P4S61




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ASROCK P4S61 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.