User manual BALAY 3VI500XA

[. . . ] en Instructions for Use Dishwasher 9000 405 273 (8811) en Index 4 4 4 4 4 4 4 5 5 5 5 6 6 7 7 7 8 8 8 9 9 9 9 9 9 10 10 10 10 11 11 12 13 14 14 14 15 15 15 15 IntensiveZone . 15 15 15 15 15 15 16 16 16 16 16 16 17 17 17 17 18 18 19 19 19 20 20 21 22 22 22 23 23 23 23 24 24 24 24 25 25 25 Safety instructions . . en Safety instructions Delivery Check the packaging and dishwasher immediately for damage caused in transit. Please dispose of the packaging material in an environmentally friendly manner. [. . . ] Press button 6 until the displayed time corresponds with your requirements. To delete the preselected starting time, is press the button 6 until indicated on the digital display. You can change your programme selection at any time until the programme starts. Interrupting the programme Switch off ON/OFF switch 1 . If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. To continue the programme, switch on the ON/OFF switch 1 again. End of programme The programme has ended when the is indicated on the numerical value display 5 . Terminating the programme (Reset) Press START button 4 for approx. Switch off ON/OFF switch 1 . 16 en Changing the programme When the START button 4 has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (reset). Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Intensive drying The final rinse uses a higher temperature which improves the drying result. Rotate programme selector 3 until is indicated on the digital display 5. (intensive The factory-set value drying off) is lit on the digital display 5. Change the setting as follows: By rotating the programme selector 3 , you can switch intensive drying on or off . The set value is saved. Overall condition of the machine Check spray arm for grease and limescale deposits. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. Health hazard! Salt and rinse-aid Check the refill indicators 9 and 8 . If required, refill salt and/or rinse-aid. 17 en Filters The filters 26 keep large foreign objects in the rinsing water away from the pump. The filter system consists of a coarse filter, a flat fine filter and a microfilter. Unscrew filter cylinder as illustrated and take out filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 23 and 24 . [. . . ] (This prevents residual water from running into the machine control and damaging the programme sequence. ) Removing the appliance Also observe the sequence of worksteps here. Pull out the appliance, carefully pulling the hose behind. Protection against frost If the appliance is in a room where there is a risk of frost (e. g. Turn off the tap, disconnect supply hose and drain water. 24 en Waste disposal Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials. Please ask your dealer or inquire at your local authority about current means of disposal. Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations (e. g. [. . . ]