User manual BALAY 3VS951BD

[. . . ] Instructions for use en 9000 041 047 (8402) en Index 4 6 6 7 8 9 10 14 auto 3in1 . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. The wooden frames (if fitted) are made of residual wood and are untreated. The hoops (if fitted) consist of polypropylene (PP). Installation Install and connect the appliance according to the installation and assembly instructions. [. . . ] As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 7 on or off. Hold down the programme button C and press the main switch 1 until the digital display lights up, then release the buttons. 5 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button C , you can switch off or switch the rinse aid indicator. on Switch off the main switch the setting is saved. 1 ; 16 en Programme overview This overview lists the max. The programmes supplied with your appliance are indicated on the fascia. Type of crockery e. g. china, pots/pans, Nondelicate cutlery, glasses, etc. Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard medium Mixed Delicate Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads very little Amount of food remains Condition of food remains Wash programme a little Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. loosely attached Intesive 70° Auto 55° /65° Eco 50° Gentle 40° Quick 45° Pre-rinse The programme sequence is optimized and adapted with how the appliance is loaded and how dirty the dishes are. Programme sequence Pre-rinse 50° Wash 70° First rinse Second rinse Third rinse Rinse-aid 70° Drying Pre-rinse Wash 50° Main rinse Rinse-aid 65° Drying Pre-rinse Wash 40° Main rinse Rinse-aid 55° Drying Wash 45° Main rinse Rinse-aid 55° Pre-rinse Drying Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching the dishwasher ON Turn on the tap. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 8 is pressed The numerical display 5 shows the expected duration of the programme. The programme starts automatically. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e. g. Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Programme progress indicator 9 Your dishes are being washed. The programme has ended. End of programme The end of programme is indicated by a buzzer. This function can be changed as follows: Hold down the Time delay programme button 4 and switch on the Main switch 1 , then release the buttons. The Time delay button 4 flashes and the digital display indicates the value (loud) which was set at the factory. Each depression of the button increases the set value by one; when is reached, the display jumps back to (off). The set value is stored in the appliance. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. [. . . ] Danger of suffocation from folding cartons and plastic film. General Built-under and integrated appliances which are subsequently installed as free-standing appliances must be secured to prevent them from falling over, e. g. by screwing them to the wall or by installing them under a continuous worktop which is screwed to the adjoining units. For Swiss version only: The appliance can be installed without difficulty between wooden and plastic walls in a kitchen range. If the appliance is not connected via a plug, the installation side must feature an all-pole disconnector with a contact gap of at least 3 mm in order to satisfy the relevant safety regulations. Notes on comparison tests You will find details of the conditions for the comparison tests on the additional "Notes on comparison tests" sheet. [. . . ]