User manual BALAY 3VT541XD annexe 2

[. . . ] Instructions for use en 9000 047 970 (8410-1) en Index 4 6 7 8 9 10 11 15 auto 3in1 . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Please dispose of packaging material properly: D The corrugated cardboard consists mainly of waste paper. D The polyethylene film (PE) consists partly of secondary raw material. [. . . ] 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 7 on or off. Hold down the programme button 3 and press the main switch 1 until the digital display lights up, then release the buttons. 4 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button 3 , you can switch off or switch on the rinse aid indicator. Switch off the main switch the setting is saved. 1 ; 17 en Programme overview This overview lists the max. The programmes supplied with your appliance are indicated on the fascia. Type of crockery e. g. china, pots/pans, Nondelicate cutlery, glasses, etc. Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard medium Mixed Delicate Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads very little Amount of food remains Condition of food remains Wash programme a little Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. loosely attached Intensive 70° Auto 55° /65° Eco 50° Gentle 40° Quick 45° Pre-rinse The programme sequence is optimized and adapted with how the appliance is loaded and how dirty the dishes are. Programme sequence Pre-rinse 50° Wash 70° First rinse Second rinse Third rinse Rinse-aid 70° Drying Pre-rinse Wash 50° Main rinse Rinse-aid 65° Drying Pre-rinse Wash 40° Main rinse Rinse-aid 55° Drying Wash 45° Main rinse Rinse-aid 55° Pre-rinse Drying Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching the dishwasher ON Turn on the tap. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 9 is pressed For appliances with top basket feature: If only the top basket is loaded, press the top-basket button 5 . The programme starts automatically. Programme data The programme specifications can be found in the summary of instructions. Greater deviations may occur due to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e. g. Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device's door. In the case of built-in dishwashers with flush front the light point will not be visible. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. [. . . ] Only this circuit breaker guarantees compliance with the currently valid regulations. Installation The required installation dimensions can be found in the installation instructions. Using the height-adjustable feet, adjust the appliance until it is level. Ensure that the appliance is standing firmly. Waste water connection See the installation instructions for the required connection steps. Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. [. . . ]