User manual BALAY 3VW300IA

[. . . ] instruction manual 9000 405 402 (8906-1) EN Dishwasher y www. balay. es Reset 3 sec. 11 10 9 8 End Start 1 2 3 4 9h 6h 3h 6 7 5 20 21 22 23 24 25 26 27 28 29 30 31 32 en Table of contents Washing the dishes . 15 15 15 15 16 16 16 16 16 16 16 17 17 17 17 18 18 19 19 19 20 20 21 22 22 22 23 23 23 23 24 24 24 24 25 25 25 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. · Hygiene * The temperature is increased during the cleaning process. chopping boards and baby bottles. Switching on the appliance ­ Turn on the tap fully. he programme starts running. § Half load * If you have only a few items to wash (e. g. It is recommended to put a little less detergent in the detergent dispenser than for a full load. ¿ Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 15 en Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. ­ Keep pressing the Preselected starting time button H until the appropriate display 3h, 6h or 9h is lit. ­ To delete the preselected starting time, keep pressing the Preselected starting time button H until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. Terminating the programme (Reset) ­ Press START button @ for approx. Switch off ON/OFF switch (. Changing the programme When the START button @ has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Rotate programme selector 8 until the "Check water supply" display h flashes. To change the setting, ­ By rotating the programme selector 8, you can switch on intensive drying (End display)" is lit) or switch off intensive drying (End display )" is not lit). The setting is saved. End of programme The programme has ended when the End display )" is lit. Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 16 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. The filter system consists of a coarse filter, a flat fine filter and a microfilter. ­ Unscrew filter cylinder as illustrated and take out filter system. Overall condition of the machine ­ Check spray arm for grease and limescale deposits. If you find such deposits: ­ Fill detergent dispenser with detergent. [. . . ] Please note the system will not function unless the power supply is connected. Transportation Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: ­ Turn on the tap. 4 minutes press the START button @ until the Cleaning display )* goes out. (This prevents residual water from running into the machine control and damaging the programme sequence. ) Removing the appliance Also observe the sequence of worksteps here. [. . . ]