User manual BROTHER HS-5300

[. . . ] English: CS-5xxx User's Guide, Preliminary (TOC) Please read this manual thoroughly before using the printer. Brother Color Printer HS-5000/5300 User's Guide Keep this manual in a convenient place for quick and easy reference at all times. English: CS-5zxx User's Guide, Preliminary (TOC) USER'S GUIDE SHIPMENT OF THE PRINTER If for any reason you must ship your Printer, carefully package the Printer to avoid any damage during transit. Warning When shipping the printer, re-pack it after waiting 30 minutes with the power off which will allow the printer to cool down and the ink to solidify. Moving the printer with ink melted will cause severe damage to the Printer and will VOID THE WARRANTY. REPACKING THE PRINTER 1 Turn the printer Off. See "REPACKING THE PRINTER" in Chapter 6. Manuals Maintenance Cassette Ink Holders Wires Printer Inside the printer, please retain the print head in position with the attached styrofoam as shown (Refer to Chapter 6, page 13. ): English: CS-5xxx User's Guide, Preliminary (TOC) (For USA & CANADA Only) For technical and operational assistance, please call: In USA In CANADA 1-800-276-7746 (outside California) 714-859-9700 Ext. [. . . ] Note Remember that the Reset button clears data from the printer memory. FF/Cont Button This button is valid only in the off-line mode. If the Data LED is on, pressing the FF/Cont button prints any data remaining in the printer after turning the printer off-line. When you select manual feed in your application, the printer alerts you to load paper in the manual feed slot by blinking the Manual LED. If a recoverable error occurs, press the FF/Cont button to recover from the error and return to the on-line state. 4­3 English: CS3 User's Guide, Chapter 4 USER'S GUIDE Shift + Test Button Set the printer to off-line by pushing the Online Button first. Pressing the Test button while holding down the Shift button starts the test print. Check the printed test page and if you find any printing problems, perform the print head cleaning as described below. Release the two buttons immediately after pressing the Test button and the DATA LED will start to blink. If it does not, the buttons were held down for too long and you will need to start the test selection again. Do not press with too much force or hold the buttons down for a long time. If you do the operation might now start. Shift + Clean Button Set the printer to off-line by pushing the Online Button first. Pressing the Clean button while holding down the Shift button starts head cleaning. If you see any problems on printouts, clean the print head and try again. Release the two buttons immediately after pressing the Test button and the DATA LED will start to blink. If it does not, the buttons were held down for too long and you will need to start the test selection again. Do not press with too much force or hold the buttons down for a long time. If you do the operation might now start. 4­4 English: CS3 User's Guide, Chapter 4 CHAPTER 4 CONTROL PANEL Test Print Mode The printer has the following test print modes. The Alarm LED blinks to indicate that the first choice, Print Config, is selected. Every time you press the button, the blinking LED changes to select another choice. LED Alarm Manual Data Ready Choice Print Config Print Fonts I Print Fonts P Test Print Function The printer prints the current printer settings. The printer returns to the ready status after printing. Note Press the buttons gently. Do not press with too much force or hold the buttons down for a long time. If you do the operation might now start. 4­5 English: CS3 User's Guide, Chapter 4 USER'S GUIDE Reset and Hex Dump print mode The printer has the following Reset and Hex Dump print modes. [. . . ] After setting the printer offline by pushing the Online Button once, execute head cleaning by pushing the Clean button while holding the Shift button. (Refer to "Cleaning the Printer Interior" in Chapter 6) When you want to perform interior cleaning, WAIT 30 minutes after turning off the printer before starting the cleaning. Select the appropriate `Envelope and Transparency' position of the head gap lever. Check the type of media in the printer driver and select the `Thick paper' position of the head gap lever. [. . . ]