User manual BROTHER LX-1200

[. . . ] Owner's Manual ® FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Note If the film is stuck, turn on the machine and press the Cut button to remove the excess film. (2) Open the film cartridge by sliding the shutter in the direction of the arrows until it locks into place. Open the film cartridge by gently separating the clear top cover from the gray bottom cover. (3) Remove the old film roll from the cartridge. - 26 - (4) Take the new refill roll of film from the sealed package. The film can only be placed into the cartridge in the correct direction. Note Remove the separator sheet between film rolls before placing the rolls into the cartridge. Please refer to the directions that are packed with the refill roll. (5) Remove the side holders (yellow color) of the film roll. (6) Close the film cartridge. Making sure that the leading edge of the film sticks out of the film slit. - 27 - (7) Press on the two shutter buttons marked "PUSH" to release the shutter. (8) The top edge of film should be aligned with the cutting line of the cartridge. If any film extends beyond the cutting line, cut away the excess film as illustrated before installing the cartridge into the machine. (9) Install the cartridge into the machine. (10) Return the roller holder to its original position and press the roller holder levers as illustrated. You will hear the roller holder click into place. - 28 - (11) Close the top cover. (12) Turn the POWER dial to Cutter Off, Border or No Border. Press the Feed button until you can see the edge of the film to remove any slack from the film. CAUTION: To prevent the film from drying out, never open the sealed pack until you are ready to install the cartridge. - 29 - Using 9" (A4) or 4. 8" (A6) film cartridges (1) Turn the POWER dial to OFF and open the top cover. (2) Pull the roller holder levers up and lift the roller holder upwards. (3) Remove the film cartridge carefully. Note If the film is stuck, turn on the machine and press the Cut button to remove the excess film. - 30 - (4) Place the cartridge adapter into the machine as illustrated. 9. 0 inch (5) Place the 9. 0 inch or 4. 8 inch cartridge into the machine. When using the 4. 8 inch cartridge, align the cartridge to the right side of the machine. 4. 8 inch (6) Return the roller holder to its original position and press the roller holder levers as illustrated. You will hear the roller holder click into place. - 31 - (7) Close the top cover. (8) Turn the POWER dial to Cutter Off, Border or No Border. Press the Feed button until you can see the edge of the film to remove any slack from the film. - 32 - Regular maintenance and troubleshooting You can keep your machine in optimum condition by cleaning it on a regular basis. Regular maintenance Avoid small debris and objects Be careful not to let anything slip into the machine, especially metal objects such as paper clips and staples. For optimum lamination results, do not place the machine and cartridges in a dusty environment. Cleaning Never use volatile liquids such as thinner or benzene to clean the exterior surface of the machine. Use only a soft cloth dampened with a diluted mild detergent solution for the exterior. Use ONLY a soft, dry cloth for cleaning the interior. Paper jams The machine will sound an alarm if a document jams while going through the feeder. Clearing a document jam (1) Turn the machine off. (2) Open the top cover. (3) Pull the roller holder levers up roller holder upwards. and lift the - 33 - (4) Remove the film cartridge from the machine. Note Use scissors or Cut to extract the jammed film and remove the film cartridge, if necessary. (5) Open the cartridge shutter and remove the document from the film slit of the cartridge. Note Do not pull the document from the opposite side. (6) Remove any excess laminating film by cutting along the engraved "cutting line" on the cartridge before reinserting the cartridge. If open, push the shutter buttons to close the shutter. (7) Place the film cartridge into the machine. Note Make sure that the film is installed correctly. - 34 - (8) Return the roller holder levers to its original position. [. . . ] Just select the picture you want to crop, click on this tool, and then move the handles on the picture to only show the part you want to see. The picture will still be intact, but you will only be able to see a portion of it. Place Toolbar The Place toolbar is a selection of automatic tools for working with all objects in PrintMaster Gold. With these tools, you can easily select pictures partially hidden behind another, group together objects you want to move as one, or flip pictures horizontally and vertically. To hide or display the Place toolbar, access the View menu, then Toolbars/Place Bar. Forward One Click this tool once to bring the active object up one level. [. . . ]