User manual BROTHER LX-900

[. . . ] Owner's Manual ® FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Other cutter units, (top/bottom cutter unit and the upper blade of the corner cutter) are not replaceable. Please consult your dealer if these cutter units become damaged. - 31 - Troubleshooting Problem No activity after the machine has been turned on. The document will not feed into the machine and alert buzzer sounds (two times). Cause The AC adapter is not connected properly. (US Letter/A4 paper cannot be laminated when a 4. 8 inch/A6 film cartridge is installed in the machine. ) The length of the document is too long. The document is too small. Solution Check that the machine is plugged into a power source. The minimum and maximum thickness of paper that can be used with this machine are 0. 1mm-0. 2mm. The width of the document must be between 2. 2" (55mm) and 8. 5" (216mm). Install the proper film cartridge. Job stops during processing, the Start button blinks (in red) and the alert buzzer sounds. Job stops during processing, the Start button blinks in orange. Output quality is poor. The length of the document must be less than 39. 4" (1000mm). Press Start to restart the process. The document will not feed straight. The document is not cut after processing. The document guide is not set properly. The cutter units have been damaged. The minimum and maximum thickness of paper that can be used with this machine are 0. 1mm - 0. 2mm. Documents must be at least 2. 2" (55mm) wide and 3. 5" (90mm) long. The maximum thickness of paper that can be used with this machine is 0. 2mm. If these cutter units do not work properly, please consult your dealer. Use Brother authorized film cartridge and film refills only. Auto Cut Mode Off is selected. The cutting position is not accurate (top/bottom) Stickers will not stick. The film cartridge is not installed properly or an incompatible film cartridge is installed. The film cartridge is not installed properly or an incompatible film cartridge is installed. The Start button blinks (in red) and the alert buzzer sounds when the machine is turned on. The Start button blinks (in red) and the alert buzzer sounds when the top cover is closed - 32 - Specifications Model number: Processing method: Power supply: LX-900/LX-910D Cold pressure method AC adapter (included) USA 120V±10% (60Hz) Output DC 18V 700mA 2. 17" ­ 8. 50" (55mm ­ 216mm) 3. 54" ­ 39. 4" (90mm ­ 1000mm) 0. 004" ­ 0. 01" (0. 1mm ­ 0. 2mm) Refillable cartridge film LC-D9 (9. 0"/A4 width double-side laminate) LC-A9 (9. 0"/A4 width adhesive-back laminate) LC-M9 (9. 0"/A4 width magnetic-back laminate) LC-D5 (4. 8"/A6 width double-side laminate) LC-A5 (4. 8"/A6 width adhesive-back laminate) LC-M5 (4. 8"/A6 width magnetic-back laminate) LC-D9/A9: About 60 sheets 11. 7"/A4 paper LC-D5/A5: About 100 sheets7"/A6 paper LC-M9: About 12 sheets 11. 7"/A4 paper LC-M5: About 20 sheets 7"/A6 paper 0. 75"/sec. (19mm/sec. ) Built-in cutting system with paper size detection Side cutter units (replaceable) Top/bottom cutter unit (non-replaceable) Corner cutter unit (replaceable ­ lower only) Side cutter units 984 feet (300m) Top/Bottom cutter unit About 5000 sheets (used with adhesive back laminate film) Corner cutter unit (Upper) 20, 000 times Corner cutter tray 3, 000 times 35 dB (stand-by mode) 357mm (W) * 293mm (D) * 195mm (H) (14. 1" * 11. 5" * 7. 7") Min. /max. thickness of document: Film: Film type: Max number of output/cartridge: Document feed speed: Cutting system: Life of the cutter: Noise level: Unit dimensions: Unit weight (not including film cartridge and AC adapter) 4. 7kg (10. 4 lbs. ) - 33 - Index A AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 10, 11, 32 Adhesive back laminate film . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Just select the picture you want to crop, click on this tool, and then move the handles on the picture to only show the part you want to see. The picture will still be intact, but you will only be able to see a portion of it. Place Toolbar The Place toolbar is a selection of automatic tools for working with all objects in PrintMaster Gold. With these tools, you can easily select pictures partially hidden behind another, group together objects you want to move as one, or flip pictures horizontally and vertically. To hide or display the Place toolbar, access the View menu, then Toolbars/Place Bar. Forward One Click this tool once to bring the active object up one level. [. . . ]