User manual BROTHER MP-21

[. . . ] Brother Mobile Full Color Inkjet Printer MP-21C/CDX User's Guide Please read this manual thoroughly before using the printer. Keep this manual in a convenient place for quick and easy reference at all times. Shipment of the Printer If for any reason you must ship your Printer, carefully package the Printer to avoid any damage during transit. The Printer should also be adequately insured with the carrier. Warning When shipping the Printer, DO NOT remove the INK CARTRIDGES from the Printer. Failure to fit the ink cartridges into the Printer during shipping will cause severe damage to the Printer and will VOID THE WARRANTY. 1 DO NOT remove the ink cartridges. [. . . ] 2-8 curl height 2-8 CHAPTER 2 PAPER HANDLING How to Load Paper in the Auto Cut Sheet Feeder (MP-21CDX or optional SF-21MP users only) 1. Make sure that the Latches on both sides of the Auto Cut Sheet Feeder are closed. Push the latches securely until you hear them click into the lock position. 2. Fig. Press the center of the Feeder cover a little and open the Feeder Cover(2). Fig. 2-10 Tilt the Feeder and Open the Cover 2-9 USER'S GUIDE 4. Align the right side of the paper against the right hand side of the Auto Cut Sheet Feeder. Adjust the Paper Guide to the left hand side of the paper and close the Feeder Cover. Fig. 2-12 Loading Paper Note When you install the Feeder onto the printer, make sure that the Feeder is straight. 2-10 CHAPTER 2 PAPER HANDLING · You can load glossy paper only from the Paper Feeding Slot or from the Straight Paper Path Slot. · Make sure the paper loaded in the Feeder is all the same type. · When adding paper, first remove any remaining paper from the Feeder and stack it with the new paper, then insert the new paper stack into the Feeder. · When you carry the printer, move the printer and Feeder carefully as shown below. Be sure to set the Printer Stand in the original position before removing the Feeder. ! Caution Fig. 2-13 The Printer and the Auto Cut Sheet Feeder Note If the paper will not load from the Feeder, use the Paper Feeding Slot and try again. Ensure that the latches are connected securely and tilt the Feeder fully. 2-11 USER'S GUIDE How to Remove the Auto Cut Sheet Feeder from the Printer 1. Fold the wire back in the Auto Cut Sheet Feeder, and close the Feeder Cover and then tilt the Feeder forwards. ! Caution Ensure you move the Paper Guide to the left, otherwise it will cause damage to the Auto Cut Sheet Feeder. Open the Latches(x) on the rear of the Cut Sheet Feeder by them forwards and push the Latches(y) on both sides inwards into the sheet feeder. Set the Latches on both sides of the Cut Sheet Feeder to the normal position. Fig. 2-15 Latches ! Caution Treat the Latches carefully so that they do not break. 2-12 CHAPTER 3 CONTROL PANEL CHAPTER 3 CONTROL PANEL LED AND BUTTONS This section refers to the following LEDs and buttons on the printer control panel. Fig. 3-1 Control Panel LEDs The (On/Off) LED (On/Off) LED indicates the current power status of the printer. Error status with the The printer is receiving data. The LED On q Off r Blinking r£q 3-1 USER'S GUIDE Ink LEDs ( (BC) LED and (MY) LED) Each Cartridge LED indicates when the ink is low or empty. LED Blinking r£q On q Printer status The color ink cartridge is running out of ink. You should replace it with a new one immediately for optimum print quality. [. . . ] · You can adjust the color by using the custom setting in the driver. Colors which printers can express and colors you see on monitors are somewhat different. The printer may not be able to express exactly some colors on your monitor. In Bi-Directional Printing, the printer prints from right to left and left to right. [. . . ]