User manual BT BIG BUTTON 100

[. . . ] If the back-up batteries are flat or not installed, your BT Big Button 100 will retain stored number information for up to 5 minutes if disconnected from the line. Replacing the batteries If you ever need to remove the batteries, firstly ensure that the phone is disconnected from the telephone line, then simply open the battery compartment cover and pull the ribbon away from the base to release the batteries. LINE R1 R2 R3 Ringer Tone TE t Mode TB HANDSET f If you need any assistance with your product, please visit www. bt. com/producthelp 6 Getting started 3. Connect the plinth for desk mounting If you are going to place your product on a desk or table then attach the plinth in the desk mounting position as shown below. Slide the plinth into the lugs marked DESK on the underside of the product. Lock/unlock switch Desk mounting lugs Once correctly inserted, turn the switch to lock the plinth into place. [. . . ] If you have new messages, the 1571 button on your AB DE BT Big Button 100 flashes. C F M1 M2 M3 M4 M5 M6 M7 M8 M9 M0 R Secrecy 123 456 789 0 GH I JKL MN O Memory PQ R TU V WX YZ Redial Messages 1571 Indicator light S 1571 lu Vo me 2. To listen to your messages, lift the handset or press Messages Handsfree , then press . Ringer volume There are three settings, Hi, Mid or Off. Handsfree Volum e 1. On the underside of your BT Big Button 100, set the Ringer Volume switch to the setting you want. Hi Lo Off Ringer Volume Ringer Tone R1 R2 R3 If you need any assistance with your product, please visit www. bt. com/producthelpTE In Using the phone Ringer tone There are three settings, R1, R2 or R3. On the underside of your BT Big Button 100, set the Ringer tone switch to the setting you want. Hi Lo Off Ringer Volume Ringer Tone R1 R2 R3 13 Recall The R button is used to access a range of switchboard TB Out services, for example, to transfer calls and with some Mode Amplify BT Calling Features or services available via your network provider. Enter a pause If your BT Big Button 100 phone is connected to a switchboard, you may need to enter a Pause in a stored number after the switchboard access code in order to give your phone time to get an outside line. This will put a delay of 2. 5 seconds in the number to be dialled. In TE A pause can be stored in the 3 one-touch and 10 memory phone numbers. If you need any assistance with your product, please visit www. bt. com/producthelp 14 Using the phone Default settings Feature Ringer volume Ringer tone Speaker volume Handset amplifier Default settings High R1 Level 3 (of 5) Level 1 (minimum) If you need any assistance with your product, please visit www. bt. com/producthelp One-touch memory buttons You can store up to three numbers using the one-touch buttons. Remove the one-touch memory label as the store button is located underneath. Press Store then press the one-touch button, you will hear a button press confirmation tone throughout the process. Lift the handset or press Handsfree 15 You can make a note of your one-touch numbers on the label above the store button. There is also an enlarged label at the back of this guide if you prefer. You may hear an exchange announcement, during or after the storing sequence, suggesting that there has been an error, or that you should redial the number. Press Store Handsfree . - memory location you want to confirm. Replace the handset or press . If you need any assistance with your product, please visit www. bt. com/producthelp Help Flashing 1571 button, but no messages I 19 The batteries may be dead. No dial tone I Check that the telephone line cord is plugged into the phone socket, see page 5. Phone does not ring I I Check that the Ringer Volume is not set to Off?, see page 12. You may have too many phones, fax machines and/or answering machines plugged in which might be overloading the sockets. One-touch buttons and Quick dial number have disappeared I Replace batteries and re-enter numbers, see pages 5, 15 and 17. Cannot hear the phone ring I Set ringer volume to Hi and change the ringer tone settings, see pages 12-13. If you need any assistance with your product, please visit www. bt. com/producthelp 20 General information This product is intended for connection to analogue public switched telephone networks and private switchboards in the United Kingdom. Safety I Do not open the BT Big Button 100 phone. There is a serious risk of explosion and/or the release of highly toxic chemicals. Cleaning Simply clean your BT Big Button 100 with a damp (not wet) cloth, or an anti-static wipe. [. . . ] This equipment complies with the essential requirements for the Radio Equipment and Telecommunications Terminal Equipment Directive (1999/5/EC). If you would like a copy of the Declaration of Conformity please visit: www. ateamtech. com/products/doc/BB100 For your records Date of purchase: Place of purchase: Serial number: For guarantee purposes proof of purchase is required so please keep your receipt. If you need any assistance with your product, please visit www. bt. com/producthelp 24 Wall mounting Screw hole 1. This prevents the handset from falling off when your phone is wall-mounted. 100mm 73mm 2. Hold the template against the wall and use a pencil to mark the screw hole. [. . . ]