User manual BT CONVERSE 2100

[. . . ] 11 General information Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Returning your phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 How many telephones can you have?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Switchboard compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 R&TTE Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Product disposal instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Wall mounting your phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 If you experience any problems, please visit www. bt. com/producthelp Getting started Location You need to place your BT Converse 2100 within 3 metres of a telephone socket so that the cable will reach. Your BT Converse 2100 can be wall mounted, see `Wall mounting your phone' on page 14. WARNING Do not place your BT Converse 2100 in the bathroom or other humid areas. Other electrical equipment close to your Converse could have an adverse effect on call quality. [. . . ] The light will not flash when used with network services such as BT 1571. Headset button & indicator Lets you make and receive calls with a headset, page 7. If you experience any problems, please visit www. bt. com/producthelp Using the phone Making and ending calls 1. Hearing Aid compatibility As this telephone is fitted with an Inductive Coupler, hearing aid wearers may benefit from switching their hearing aid to the middle `T' position and holding the earpiece up to the aid, not their ear. Please visit http://www. btplc. com/inclusion/ for further practical advice on using hearings aids. Make a call using a headset Headsets are not supplied with your BT Converse 2100. However, you can purchase headsets (with RJ11 jack) by visiting www. shop. bt. com 1. on the underside 7 indicator (on the Press to end the call. Receive a call using a headset 1. When the phone rings and the headset is plugged in, press Redialling the last number The redial number can up to 32 digits long. If the last number dialled was longer than 32 digits, only the first 32 digits will be dialled. to answer. If you experience any problems, please visit www. bt. com/producthelp 8 Using the phone Secrecy During a call, you can talk to someone nearby without your caller hearing you. The red secrecy light (on the button) comes on and your caller cannot hear you. Press again to return to your caller. Message waiting If your BT Converse phone is connected to a switchboard, the message waiting indicator will flash when you receive new voicemail messages. BT 1571 or similar network voicemail users can also use this feature, however the indicator light will not flash. New voicemail messages will be indicated by a stuttered dial tone when you pick up the handset. Message waiting switch If your telephone is connected to a switchboard you may need to change the message waiting switch setting on the base of the phone. MW1 and MW2 positions are for when the telephone is connected to an ISDX switch. If the switch is moved to MW2 and the message waiting indicator stays on permanently, use MW1. 1. Lift the handset, or press your answering service. and dial to connect to If in doubt, please refer to your PBX instructions/manager for the correct procedure to access this service. If you experience any problems, please visit www. bt. com/producthelp Using the phone 9 Adjusting the ringer volume 1. Set the Ringer Volume switch on the underside of the phone to 0 (Off), 1 or 2. Adjusting the ringer tone 1. Set the Ringer switch on the underside of the phone to 1 (Low), 2 (Medium) or 3 (High). R (Recall) The button is used to access a range of switchboard services, for example, to transfer calls and with some BT Calling Features. Press to switch the earpiece/headset volume between Normal and High. After you hang up, the volume will automatically return to Normal volume. If you experience any problems, please visit www. bt. com/producthelp 10 M1 ­ M3 memory buttons Each number can be up to 32 digits long and can include a pause or #. If you enter more than 32 digits you will hear an error beep. You can store your 3 most frequently used phone numbers on the one-touch memory buttons ( , and ) and dial them by pressing a single button. Store/replace a one touch number 1. or button you want until you hear a beep and the Secrecy light flashes. To enter a pause when storing a number press . 3. [. . . ] To switch to tone dialling during a call, press . recycling processes. For more information please contact your local authority or the retailer where the product was purchased. Product disposal instructions for business users Business users should contact their suppliers and check the terms and conditions of the purchase contract and ensure that this product is not mixed with other commercial waste for disposal. R&TTE Directive This product is intended for use within the UK for connection to the public telephone network and compatible switchboards. This equipment complies with the essential requirements for the Radio Equipment and Telecommunications Terminal Equipment Directive (1999/5/EC). If you experience any problems, please visit www. bt. com/producthelp 14 Wall mounting your phone WARNING Before you wall-mount your BT Converse 2100, check that you are not drilling into any hidden wiring or pipes. [. . . ]