User manual BT CONVERSE 320

[. . . ] Open the battery compartment cover. 2 Insert batteries as shown. 1 Press the Store button. 2 Press the Clock button. Your Converse 320 is only designed to be operated in a normal office or domestic environment. It should not be used in bathrooms or near water. 3 Close the lid and replace the compartment cover. 3 Enter the current time Plug your Converse 320 into the phone socket using the 24-hour clock, eg. 0 9 3 0 = 9. 30am, 1 5 3 0 = 3. 30pm. 4 Press the Store button. Check your telephone wall socket The time is set and displayed. Check the dialling mode If you do not have a modern-style socket, call Freefone 0800 800 150. P T TB MODE Your Converse 320 is now ready for making and receiving calls. 1 Set the dialling mode switch on the underside of your Converse 320. It should be set to TB. Using your Converse 320 Emergency calls You hear the dialling tone. Using a headset 2 Dial the number you want. The display shows the number dialled. 3 When your call is answered, either lift the handset or speak in `handsfree' mode. [. . . ] Lift the handset to answer the call. Set the ringer tone switch on the underside of your Converse 320 to the setting you want: R1 for a low pitch ring or R2 for a high pitch ring. R1 R2 RINGER Message Waiting indicator engaged tone, press the Redial button. When you have Voice Mail messages waiting, the Message Waiting indicator will flash at regular constant intervals. To adjust the caller's speech volume 2 Replace the handset (or During a call, you can make your caller's voice louder. When using Handsfree: Press the VOL + or VOL button to increase or decrease the volume of your caller's voice. Note press the Handsfree or the Headset button - depending which mode you are in). Ten seconds after the handset is replaced, your Converse 320 will switch to `handsfree' mode and the number is redialled. This feature is for Meridian switchboard users only. When using the handset or a headset: 1 Press the Amplify button. 1 Press the Store button. To dial a two-touch number The number is stored. 1 Press the Handsfree button. 2 Press the VOL + or VOL - button to increase or decrease the volume of your caller's voice. To change a stored number, repeat the steps shown above. The new number will replace the existing one-touch number. 2 Press the Shift button. 3 Press the Memory button To store a one-touch number in the memory you want. To dial a one-touch number eg The number is dialled. Your Converse 320 can store up to 20 telephone numbers: 10 one-touch numbers under the memory buttons and 10 two-touch numbers, using the memory buttons with the Shift button. Stored numbers can be up to 21 digits long and include the D and # buttons and a pause. Use the label to keep a directory of each one-touch and two-touch number. One-touch memory buttons 6-10 (the bottom 5 buttons) are pre-set with BT Select Services numbers (see `Using Select Services'). These can be overwritten if you wish. Press the Handsfree button and press the memory button you want. eg To store a number longer than 21 digits The number is dialled. To store a two-touch number in the memory Store the first 21 digits as shown previously, then repeat the steps to store the remaining digits under another Memory button. 1 Press the Store button. To dial a stored number of more than 21 digits 1 Press the Handsfree button. 2 Press the Memory button 2 Press the Shift button. 3 Press the Memory button which contains the first 21 digits. 3 Press the Memory under which you want to store the number. eg button which contains the remaining digits. The number is dialled automatically. 1 Press the Store button. 4 Enter the phone number you want to store. 2 Press the Memory button under which you want to store the number. eg 5 Press the Store button. The number is stored. 3 Enter the phone number you want to store. To store a pause in the number Using the calculator Memory back-up A pause is sometimes required with switchboards and network services. A pause simply gives the switchboard a few seconds to pick up the outside line before dialling. Using the Redial button, you can insert a pause in numbers stored in the memory. Press the Calculator button. The display will change to the calculator function. Use the numbers and calculator functions on the memory buttons as you would a conventional handheld calculator. Use the # button to enter a decimal point. If you unplug your Converse 320 from the telephone socket and it has fully charged batteries, it will keep all the numbers you have stored in the memory. However, if you unplug your Converse 320 and your batteries are totally discharged, numbers stored in the memory will be maintained for about 5 minutes only. Pre-programmed BT Select Services numbers will not be affected. When your batteries are within about two weeks of total exhaustion, BATT LOW will appear in the display. If you do not replace the batteries and they become totally discharged your Converse 320 will not display anything on the screen. Repeat the steps for storing a number in the memory but press the Redial button where you want to add a pause within the number. Press the Calculator button at any time to return the display back to normal. To set the call timer Recall button 1 You can time each call. You can stop the time by pressing the Clock button once more. The Recall button is for use with switchboard services and some BT Select Services. 3 When you replace the handset or press the Handsfree button to end the call, the display shows the final duration of the call for a few seconds before returning to the normal clock setting. Using BT Select Services Note Call Return Call Return tells you the number of the last person who called you and the time and date the call was received. 1 Press the Handsfree button. 4 Press the # button and listen for confirmation of your instructions. 5 Press the Handsfree button. A switchboard can provide a similar range of functions to BT Select Services. 1 6 3 0 books a Reminder Call at 4. 30 pm. 4 Press # and listen for Call Waiting During a call, a discreet `beep' lets you know another person is trying to get through. You can put your original caller `on hold' and switch to the new caller. For information on these and many other valuable services, call BT on 152. [. . . ] If you do not have a compatible switchboard, it cannot be guaranteed that your Converse 320 will operate correctly under all possible conditions of connection. Guarantee If you own your Converse 320 under BT's guarantee, BT guarantees the product for one year provided that: The goods have only been used for their intended purpose and have not been subjected to misuse, or been wilfully or accidentally damaged. The goods have not been tampered with or repaired by anyone other than BT, its staff or agents. If a fault does occur in this product, and you bought the unit yourself, provided that you return it to the place of purchase and produce your receipt, it will either be repaired or replaced free of charge. [. . . ]