User manual BT SYNERGY 3500

[. . . ] Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 SE C RA S W VIC LL NE UB Y O E ER T SC O RK S D W R U BE IS OR IB M . A P EU Q FOR LAY K P TO ST UA E A R RT TH ND OV YO ER ES C ID UR LY E AL ER FE FEA L W 'S E T AIT IS UR IN PA ES G YA W BL IL EL This equipment is not designed for making emergency telephone calls when the power fails. Alternative arrangements should be made for access to emergency services. This product is intended for connection to analogue public switched telephone networks and private switchboards in the United Kingdom. Synergy 3500 Digital Cordless Telephone Answering Machine with Caller Display* and Call Waiting* User Guide Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 Please open this page for an `at a glance' guide to your Synergy 3500 Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 Please open this page for a further `at a glance' guide to your Synergy 3500 Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 At a glance Volume buttons Use to adjust the handset earpiece speech volume (see page 19) and handset and base ringer volume, see pages 25 and 28. Also used to access the redial and calls list and scroll through the directory, menu options, redial and calls list. [. . . ] The display will show EMPTY for 2 seconds. R Secrecy Note You can switch back and forth between the two calls without disconnecting either if you wish. Menu 33 Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 If you wish to disconnect the first call press the TALK button after speaking to the first caller. Press the TALK button again and continue with the second caller. Note The second caller will only be charged for their call from the moment you answer and not while they are waiting for your initial contact. CALL WAITING 34 Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 Setting up and personalising your answering machine Your Synergy 3500 can digitally record up to 13 minutes of messages, with each message lasting a maximum of 3 minutes. As well as recording incoming messages, you can record memos for other users. You can operate your Synergy 3500 from: · The base unit. ANSWER MACHINE Page DECT Digital Clarity Ans. on off Vol. Skip Stop Skip Del Play DISPLAY (Blank) DEFINITION Power off. The display flashes between a dash and the number of messages saved in the memory. Your Synergy 3500 comes with two pre-recorded outgoing messages, Answer and Record or Answer Only, but if you wish you can record your own. You will need to set the day and time (if you have not already done so) so that you will know when each message was received, see page 15. C-0 (flashing) 0-9 9 (flashing) ­­ Alternating with 0-9 A (flashing) E (flashing) F (flashing) P (flashing) P-1: Alternating between P & 1 Message display on the base station The table opposite provides an explanation of what is shown on the base station display. P-2: Alternating Answer Only outgoing between P & 2 message. r (flashing) Message recording (memo, outgoing message or incoming message). Counting down. t or 2 to 9 8-0 35 Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 To switch the answering machine ON/OFF To adjust the base unit loudspeaker volume Your Synergy 3500 is set to ON and Answer and Record when first powered up. Ans. on off Press and release the ANSWER ON/OFF button to switch ON or OFF. If you hear "Answer on, your outgoing message is. . . . " the answering machine is switched on and is ready to answer incoming calls and record any messages, unless Answer Only is selected. Answer Only is an advisory announcement only, so that the machine will not record an incoming message. See page 38 for a full explanation of the outgoing messages available. The display on the base unit shows the number of messages stored in the memory. If you hear "Answer off" the answering machine is switched off. The display on the base unit will flash between a dash and the number of messages saved in the memory. Vol. Vol. The loudspeaker volume ranges from 0-9 plus H, where 0 is Off and H is the maximum level. If you adjust the volume when the answering machine is not being used, a beep sounds at each press. When the volume reaches its highest or lowest levels two beeps will sound. ANSWER MACHINE Answer delay Answer delay sets the number of times your Synergy 3500 will ring before the answer machine picks up your call and starts playing the outgoing message. The default setting is for the answering machine to answer after 6 rings. You can change this setting to between 2-9 rings. 36 Synergy 3500 user guide ~ 3rd Edition ~ 21st October '02 ~ 4461 To change the answer delay setting Audible Message alert When audible message is switched ON and new messages have been received, your Synergy 3500 will beep every 10 seconds. The volume of the beep is at the volume you have set for the loudspeaker. [. . . ] All items of telephone equipment have a Ringer Equivalence Number (REN), which is used to calculate the number of items which may be connected to any one telephone line. A total REN of 4 is allowed, if the total REN of 4 is exceeded, the telephones may not ring. With different telephone types there is no guarantee of ringing, even when the REN is less than 4. Only use approved power supply, item code 005391 for base station or 003313 for charger (only applicable if you have purchased the Synergy 3500 Twin). [. . . ]