User manual CANDY CCE 16 X,MV

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANDY CCE 16 X,MV. We hope that this CANDY CCE 16 X,MV user guide will be useful to you.


CANDY CCE 16 X,MV : Download the complete user guide (238 Ko)

Manual abstract: user guide CANDY CCE 16 X,MV

Detailed instructions for use are in the User's Guide.

[. . . ] As previously specified in the chapter "Warning" remember there must be a minimum of 650 mm between the bottom edge of the hood and the stop of the stove. Secure the metal bracket (B) to the wall using the screws and plugs (bracket, screws and plugs are all supplied with the unit). Use the 2 triangles cut into the bracket to position it precisely along the vertical axis of the hood. Adjust the horizontal position, shifting the hood to the right or left as needed lining it up with the wall units. [. . . ] Once regulation has been completed, finish securing the hood with 4 more screws (M): mark the points for the 4 holes on the wall, remove the hood and drill (8mm diameter holes); then use the plugs and screws to complete installation. Rest the lower edge of the panel behind the stove and anchor the upper edge to the wall using the two holes found on the panel. The unit is secured to the rear panel as though it were being installed on the wall: use the supplied metal bracket (B) and the screws and plugs supplied with the panel. Securing the extension flues: Basic installation requirements: ­ Set the electrical power supply within the space covered by the decorative flues. ­ If your unit is installed in an Exhaust hood or in a hood with outside motor, prepare the air exhaust hole. When installing exhaust hoods and hoods with outside motor, to achieve the best possible conditions use an air exhaust pipe that : i) is as short as possible, ii) has a minimum of curves (maximum angle: 90°), iii) is made of a material that complies with the standards (which vary from nation to nation) and iv) is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section (diameter: 150 mm). Adjust the width of the extension flue support bracket (W) using screws A indicated in Fig. For exhaust hoods, turn the upper flue over so that the air exhaust grid is in the lower section (Fig. Be very careful when handling the telescopic flues, especially when resting these on the hood body, to prevent scratching. Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down for about 1", the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button C: drives the motor in second speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button D: drives the motor in third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button E: drives the motor in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on), the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Pay special attention to the grease filters: if the model purchased has the controls shown in Figure 17: the grease filters must be cleaned approximately once every 30 hours of operation (when the central segment on the display goes on or starts blinking). to remove the filters: press inward on the clamps at the handles and pull the filter downward. Once the cleaned filters are reinstalled, keep button R (Reset) pressed for two seconds to reset the counter. If the model purchased has the controls shown in Figure 18/19/ 20: the grease filter must be cleaned periodically: exactly how often depends on use (at least once every other month). To remove the filter: push inward on the clamp at the handle and pull the filter downward. If the model purchased has the controls shown in Figure 21: the grease filters must be cleaned approximately once every 30 hours of operation (when the light button lamp comes on) - Fig. [. . . ] If the model purchased has the controls shown in Figure 21: the grease filters must be cleaned approximately once every 30 hours of operation (when the light button lamp comes on) - Fig. Once the cleaned filters are reinstalled, to reset the counter hold the light button pressed down for about 1" (Fig. Replacing the charcoal filters: If the unit is a filtering hood, the charcoal filters must be replaced: to remove them press inward on the clamp (Fig. 16) and rotate the filter downward until the 2 tabs can be removed from the housing. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CANDY CCE 16 X,MV




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANDY CCE 16 X,MV will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.