User manual CANDY PV640SN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANDY PV640SN. We hope that this CANDY PV640SN user guide will be useful to you.
Manual abstract: user guide CANDY PV640SN
Detailed instructions for use are in the User's Guide.
[. . . ] a plastic bag containing : - the new jets for the gas modification, if required, - according to model, a cylindrical connector and/or a conical connector with seal for the gas connection, - the fixing brackets with screws required for installing the hob in the worktop. rECOMMENDATIONS
TO GET THE BEST FROM YOUR APPLIANCE , PLEASE READ THE FOLLOWING CAREFULLY. Please keep the operating and installation instructions in a safe place for future reference. Before fixing the hob, note the serial number of the appliance just in case you should require future repairs from our after sales service organisation at some time in the future. [. . . ] CONNECTION BY RIGID PIPE Connect directly to the threaded end of the inlet pipe. CONNECTION BY FLEXIBLE PIPE WITH MECHANICAL CONNECTOR Screw the nuts of the flexible pipe directly on to the inlet pipe at one end and the gas supply stop tap at the other. 21
INSTALLATION: ELECTRICAL CONNECTION
The mains electricity supply connected to the appliance should comply with the norms in force in the country of installation. Connection to the mains electricity supply should be through a socket with an earth terminal, or through an intermediary switching device with a gap between contacts of at least 3 mm. The power supply unit must be protected by appropriate fuses and use cables of a large enough cross section to provide a normal supply to the appliance. The hob is fitted with a power supply cable* without plug which allow it to be connected only to a power supply of 230 V between phases, or between phase and neutral. Warning : before proceeding with the connection, check the continuity of the earthing of the power supply unit. We cannot be held responsible for any accident which has resulting from the use of an appliance which is not connected to earth, or whose earthing is defective. * The eventual replacement of the supplying cord must be carried on by the After Sales Service or by an agreed engineer, with a cord whose characteristics must be similar to the original one. SETTING THE IDLE FLAME
If you have changed the type of gas, it is important to verify the flame stability at the minimum regulation. Gaining access to the by-pass screw To gain access to hob burner by-pass screws, remove the knobs from the control panel. By-pass screw of the hob burner
REGULATING THE MINIMUM FLAME ON THE HOB BURNER a) Natural gas : . Turn the control knob from minimum to maximum position to check that it is satisfactory. B) Butane-propane gas : The by-pass screw should be screwed fully home, without being locked. 23
THE GAS BURNER
THE ULTRA-RAPID BURNER or "4 RINGS" BURNER, power rating 3, 5 kW : use this burner for bringing to boil, for cooking large quantities, and generally for all foods requiring rapid cooking. THE FAST BURNER, power rating 2, 5 kW : use the large burner for all foods requiring rapid cooking. THE SEMI-FAST BURNER, power rating 1, 75 kW or THE AUXILIARY BURNER, power rating 1kW : it is ideal for stewing, sauces and slow cooking. The pan supports fitted on the 1, 75 kW burners are working as Mijorose when the burner is set on low rate. On the slow setting, the flame only comes into contact with the cast iron burner cap. This is ideal for slow cooking, as the heat is evenly distributed under the pan and food doesn't dry out or stick to the bottom of the pan. On the high position, the flames heat directly the pan allowing all cookings on quick gas. For a proper use of the burners, choose pans which match the dimensions given below : * Ultra-rapid or "4 Rings" 18 cm and more * Rapid 16 to 18 cm * Semi-fast 12 cm * Auxiliary 10 cm
SOME TIPS . [. . . ] Place a few drops of the specialised cleaning products on the hob surface. Burner caps and pan supports : the pan support is made of enamelled cast-iron and the burner cap is made of enamelled steel, for a maximal protection and an easy cleaning. Do not immerse them in cold water immediately after use to avoid cracking the enamel from the thermal shock. The use of abrasive cleansers is not recommended as they scratch and dull the enamel. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CANDY PV640SN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANDY PV640SN will begin.