User manual CANON RAD DSC 2H2010 BROCHURE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANON RAD DSC 2H2010. We hope that this CANON RAD DSC 2H2010 user guide will be useful to you.
Manual abstract: user guide CANON RAD DSC 2H2010BROCHURE
Detailed instructions for use are in the User's Guide.
[. . . ] For Users in the UK When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover. CHANGING THE FUSE THE MAINS LEAD ON THIS PRODUCT IS FITTED WITH A NON-REWIREABLE (MOULDED) PLUG, INCORPORATING A 3 AMP FUSE. SHOULD THE FUSE NEED TO BE REPLACED AN ASTA OR BSI APPROVED BS1362 FUSE OF THE SAME RATING MUST BE USED. CHANGING THE PLUG IF THE FITTED PLUG IS NOT SUITABLE FOR YOUR SOCKET OUTLETS, IT SHOULD BE CUT OFF AND AN APPROPRIATE PLUG FITTED IN ITS PLACE. [. . . ] The digital signals can be output to the other equipment with a DV terminal. The camcorder's DV terminal works exclusively as an output terminal. · There may be cases where analog-digital conversion cannot be done properly, depending on the signals output from the connected equipment. For example: Signals that include the copyright protective signal, or anomalous signals such as ones that include ghost signals, etc. Even if the AV/headphone terminal is set to "PHONES" through the menu, it will automatically be set to "AV", and "PHONES" will disappear from the display. · You are recommended to use power from a household power socket with the power adapter. · Turn off the power of all equipment before performing connections. · Refer also to the instruction manuals of the other equipment connected.
: Signal flow
OUTPUT
E
S-150 S-Video Cable
S(S1)-VIDEO
Editing
VIDEO
AUDIO
AV IN/OUT
MIC
STV-250N Stereo Video Cable
L R
IN/ OUT
Side with arrow
CV-150F DV Cable
Above illustration shows the connection using a S-video cable. You can also connect to the VIDEO terminal instead ( 36).
95
E
Turning the Analog-Digital Converter On
TAPE
+
PLAY (VCR)
VCR SET UP
AV
DV OUT···OFF
(
38)
To turn the analog-digital converter on, open the menu and select VCR SET UP. OR Press the AV \ DV button on the wireless controller.
Caution: · For normal use, set AV \ DV OUT to OFF (so that AV \ DV does not appear in the display). If it is set to ON, you cannot input digital signals through the camcorder's DV terminal. Make absolutely sure to set the audio mode of the new tape to 12-bit and the recording mode to SP. To connect other audio devices:
: Signal flow
OUTPUT
AV IN/OUT
STV-250N Stereo Video Cable
AUDIO L R
An audio device (i. · The AV terminal doesn't put out any video, so connect the S-video terminals and check your TV, or check the LCD or the viewfinder as you add new sound. To connect an external microphone:
100
Editing
Notes: · When you add sound using the built-in microphone make sure not to connect any cables to the MIC terminal. · To use your TV to monitor video, connect the S-video terminal ( 35) or the AV terminal (use only the video plug) to your TV. You can monitor the sound with headphones only when using the S-video terminal ( 33).
E
Preparations
Turn the camcorder's POWER switch to PLAY (VCR) and move the camcorder's TAPE/CARD switch to TAPE. · Make sure the REC/SAVE tab on the cassette has been slid to REC (closed position).
Dubbing
REC PAUSE
ZERO SET MEMORY
/ /
REW /
PLAY STOP SLOW
MENU
FF +/ ×2
SET
Do not connect/disconnect any cables to/from the camcorder when dubbing audio or preparing to dub audio.
TAPE
+
PLAY (VCR)
VCR SET UP
(
38)
1. Locate the point where you wish to start audio dubbing, then press the PAUSE button.
· You can use the playback buttons on the body of the camcorder or the special playback functions on the wireless controller in the same way as in playback mode. · The camcorder becomes set to playback pause mode.
CA M
(V CR)
E
RA
O FF PL A Y
AUDIO DUB. PAUSE
AV INSERT
AV DV
Editing
AUDIO DUB. ··AUDIO IN
101
5. Press the PAUSE button (and start play on the other audio device if AUDIO IN).
· Audio dubbing starts. [. . . ] The printer is printing the data from a memory card inserted into the computer or printer. The printer automatically starts printing the images from the camcorder after completing the current printing. If you select [Continue] in the error screen, you can restart printing. You can restart printing by pressing the RESUME/CANCEL button on the BJ Printer. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CANON RAD DSC 2H2010
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANON RAD DSC 2H2010 will begin.