User manual CARDO SCALARIDER TEAMSET PRO

[. . . ] TM TeamSet PRO TM communication in motion TM User Guide Gebrauchsanleitung Guide d'Utilisation Guida di Avvio Guia de Usario © Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. 2 scala rider® TeamSetTM PRO INTRODUCTION Congratulations and thank you for choosing the scala rider TeamSet pro Bluetooth® Headset package for bikers. This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider TeamSet pro. [. . . ] Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp's back plate. Determine the location on the helmet where the Helmet Clamp must be attached. 3. Adjust the Helmet Clamp's location on the Helmet so that the microphone is located opposite your mouth. You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally (Be sure to clean the selected area prior to the gluing process). Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Therefore it is recommended to not use the headset during this 24 hour period. Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed. Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, you Cable should tuck away the long corded speaker underneath the helmet Speaker B padding as follows: Lead the speaker cord [B] alongside the rim of the padding to the right side and then back to Speaker B the left side, near speaker [A]. Then place the speaker [B] underneath the padding. English Speaker A POSITIONING THE SPEAKERS Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for the left ear [A] and the long speaker cord [B] for the right ear). You may want to use the supplied Velcro pad. Speaker A ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP ATTACHING: Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING: Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle. Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections. Terminate a call Voice Dial PHONE FUNCTIONS Tap the CTRL Button to end a call. During Standby, tap the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. Press and hold the Volume Down Button for three seconds during Standby. English Redial Enable/Disable Voice Connect feature (VOX) The scala rider TeamSet pro offers VOX technology for safe and hands-free operation of some key functions. To reject an incoming call, you need only to remain silent for about 15 seconds. While on standby press and hold the Volume Up and Volume Down Buttons simultaneously for three seconds until you hear a beep. NOTE: The Enable/Disable Voice Connect feature affects only the Intercom functionality. NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS device, not directly to the scala rider TeamSet pro, some of the above Phone functions may not be available. When the headset is on an active phone call, any Buddy Intercom call request will be rejected automatically. Once the phone call audio link drops, you can initiate and accept Buddy Intercom calls. STATUS LIGHT STATES None Alternating red/blue flashes Rapid red flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds 1 red flash every 3 seconds 2 red flashes every 3 seconds Solid red Headset is off Mobile phone/GPS Pairing mode Intercom Pairing mode Standby ­ No call is in progress Call is in progress Battery is low Low battery while a call is in progress Headset is being charged scala rider® TeamSetTM PRO 9 MAKING AND RECEIVING MOBILE PHONE CALLS Answer a call Reject a call PHONE FUNCTIONS Tap the CTRL Button or speak loudly any word of your choice during an incoming call. [. . . ] End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. European CE Notice The scala rider TeamSetTM pro headset (the "Product") is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3. 1a, 3. 1. b and 3. 2. The Product is manufactured in accordance with Annex II of the above directive. [. . . ]