User manual CATERPILLAR PM201 BROCHURE

[. . . ] PM201 Cold Planer Cat® C18 Engine with ACERT® Technology Gross Power 485 kW Rotor Width 2100 mm Rotor Depth (maximum) 305 mm 650 hp 83" 12" Operating Weight with conical rotor with breakaway rotor with weld-on rotor 39 165 kg 38 145 kg 38 050 kg 86, 360 lb 84, 105 lb 83, 905 lb PM201 Cold Planer The new PM201 combines enhanced production capabilities, optimized performance and simplified service to complete tough milling applications with productive results. C18 Engine with ACERT® Technology ACERT® Technology works at the point of combustion to optimize engine performance and provide low exhaust emissions. The C18 engine with ACERT® Technology provides clean burning power. Load sensing system controlled by the ECM, matches propel speed to load on engine for maximum production. [. . . ] Self-diagnostics provides information for troubleshooting and alerts the operator of potential system problems. Automatic load control adjusts propel speed so that engine speed is maintained at no less than 1900 rpm. Steering control provides four steering modes for maneuvering in tight quarters: front steer only, crab steer, coordinated steer and rear steer only. 8 Automatic Grade and Slope Control The optional contacting or non-contacting grade controls provide precise control of the machine to a preset cutting depth. Contact or non-contact grade sensors can be positioned on each side are easy to position and provides a consistent accuracy to ± 3 mm (1/8"). Contacting wire rope grade sensor measures side plate movement that enables the entire length of the side plate to become an averaging device for extremely accurate grade matching. Remote mounted control boxes allow manual or automatic operation from either the operator's station or at ground level. Maintenance-free Caterpillar batteries are mounted on the top of the machine and are accessible through a bolt-on cover. Cat batteries are specifically designed for maximum cranking power and protection against vibration. Cooling package is a multi-row modular design, stacked in series for easy access for cleaning and service. A modular stacked cooling system provides more efficient cooling of individual systems and makes replacement and routine cleaning easier. The power-assist engine hood opens wide to provide walk-in access to the engine, air filter, hydraulic components and daily service points. Electronically controlled on-demand variable speed cooling fan provides the lowest overall noise levels and high ambient operation capability. Engine Gross Power SAE J1995 Net Power ISO 9249 EEC 80/1269 SAE J1349 Specifications Bore Stroke Displacement I Propel System Hydrostatic drive with hydraulic flow provided by a variable displacement piston-type pump. Drive motors with planetary gear reduction on each track provides balanced tractive effort. Features Rotor Drive System Operates direct through a hydraulically actuated, Caterpillar wet clutch driving a Caterpillar planetary gear reducer located inside the rotor mandrel. 1 liters 1105 in3 I I I I I I I The power ratings apply at a rated speed of 2100 RPM when tested under the reference conditions for the specific standard. The net power advertised is the power available at the flywheel when the engine is equipped with an alternator, air cleaner, muffler and fan at minimum speed. The net power at the flywheel when the fan is at maximum speed is 445 kW (597 hp) per the SAE J1349 reference standards. Dual fuel filters with water separator and air compressor are standard. i I I I A variable displacement , piston-type pump with electronic displacement control supplies pressurized flow. Positive traction control valve provides equal hydraulic oil flow to each drive motor to increase tractive effort in hard or deep cuts. [. . . ] Track assembly features track frame stops to limit track angles to provide machine's ability to propel up inclines and out of deep cuts. PM201 specifications 13 Optional Equipment Note: Some options listed may be an option in some areas and standard in others. Hydraulically Operated Front Door provides an adjustable down pressure to prevent slabbing of the road surface in front of the machine resulting in optimum sizing and gradation. Hydraulically Operated Side Plates allow ground personnel to raise/lower side plates to precisely place the rotor against gutter pans or when working near obstructions. [. . . ]