User manual CISSELL 36BD30

[. . . ] The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. [. . . ] (7. 26 kg) Page 4 Page 5 SPECIFICATIONS Boiler Horsepower . . . . . . . . . . . . . . . . . 1 1/4 60 to 100 1/2 Pipe 1/2 Pipe Installation Instructions Make Steam Supply and Steam Return Connections as Illustrated Whenever possible, horizontal runs of steam connections must drain by gravity to respective Steam Holder. Each Steam Holder must drain, by gravity, to boiler or condensate return tank. To prevent condensate draining from Steam Holders to machine, make steam connections to each respective Header with a 12 Inch (or more) vertical riser. Do not make steam connections to a Header with a horizontal or downwardly facing tee or elbow. Water pockets, or an improperly drained steam line (or header) will provide wet steam, causing unnecessary wetting-out of buck padding and improper operation of steam iron. INSTALL STEAM PIPING IN ACCORDANCE WITH ALL LOCAL REGULATIONS AND REQUIREMENTS Y STRAINER & THERMODYNAMIC TRAP MAY BE SUBSTITUTED. Before installing check valve and trap w/built-in strainer, open globe valve in the supply line and allow to flush out any foreign matter that may be in the casting and pipes. If steam is gravityreturned to boiler, omit trap but install check valve in return line near machine. NOTE: For successful operation of machine, install trap as close to floor and as near machine as possible. Inspect trap carefully for inlet and outlet marks and install according to manufacturers instructions. Make certain that steam supply, steam return, and electrical connections have been made per installation instructions. If iron lowboy has a separate steam supply and return valves, open them also. STEAM SUPPLY: Steam supply connection must fall towards machine (without water packets). Make connection with 12 or more riser out of steam supply line with union and globe valve. (NOTE: If machine is on the end of a line of equipment, then extend steam header line at least four feet beyond machine. If gravity return omit trap. ) STEAM RETURN: If steam is returned to atmosphere or sewer, make steam return connection with union, globe valve, check valve and trap with drain. If steam is gravity returned to boiler, omit trap, but install check valve in return line near machine. (NOTE: For successful operation of machine, install trap as close to floor and as near machine as possible. Inspect traps carefully for inlet and outlet marks and install according to factory instruction. BLOW SCALE AND DIRT FROM STEAM LINES BEFORE INSTALLING TRAP TO INSURE PROPER OPERATION. ) WIRING: Check Voltage and current of solenoid valve MECHANICAL SPECIFICATIONS and see that they correspond with power line before making installation. NOTE: Connect power supply to terminals in electric box as per wiring diagram in accordance with electric code in your area. FOR THREE PHASE CURRENT: Connect two wires from three phase supply to two Power Connections of outlet box. IMPORTANT: Connect ground wire as shown and check all wiring before closing switch. [. . . ] PULL LEFT CORD AT HEEL OF CLOTH ACROSS AND THOUGH SLOT A ON RIGHT SIDE OF CLOTH. BRING CORD FROM B UP AND AROUND COLUMN MOUNTING AND THROUGH SLOT C ON LEFT SIDE. PULL RIGHT CORD AT HEEL OF CLOTH ACROSS AND THOUGH SLOT 1 ON LEFT SIDE OF CLOTH. PULL CORD BACK ACROSS AND UP THROUGH GROMMET 2 ON RIGHT REAR OF CLOTH. 6. 7. 8. 9. 10. [. . . ]