User manual CISSELL AF1MAN60

[. . . ] No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization from Cissell. Charges for unauthorized repairs will not be accepted or paid by Cissell. CISSELL MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, STATUTORY OR OTHERWISE, CONCERNING THE EQUIPMENT OR PARTS INCLUDING, WITHOUT LIMITATION, A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, OR A WARRANTY OF MERCHANTABILITY. THE WARRANTIES GIVEN ABOVE ARE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. [. . . ] Conversely, if the revolving form rides too high above the Form Finisher base, permitting steam to escape from the space between the form and base, the form must be lowered. WHEN AN ADJUSTMENT MUST BE MADE, REMOVE REVOLVING FORM BY SIMPLY LIFTING IT SRAIGHT UP OFF THE FORM FINISHER BASE PROBLEM: Revolving Form "drags" on base of Form Finisher TO CORRECT: Loosen F-286 Bearing Lock Nut. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too low. . . or too high. . . repeat adjustment until it is correct. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too high. . . or too low. . . repeat adjustment until it is correct. Page 10 F517 - Adjustable Shoulder Assembly Consists of 1-10, 18, 19, 20. REVOLVING AIR FORM REVOLVING FORM AF115 - Revolving Form w/Front & Rear Clamps AF181 - Revolving Form w/o Clamps Ref. TU3478 F381 Description #8 x 1/2" Screw Shoulder Adjustment Rod, Knob, & Pin F49 Shoulder Lever Pin F192 Insulating Gskt. (2 required) F492 Neck Form w/4 Bolts, Nuts & Washers F493 Shoulder Extension F336 Shoulder Connecting Link F494 Bearing Plate w/Scrs. AF207 Collar AF153 Form Assembly TU3477 #10 - 24 x 1/2 Screw FB187 #10 Lockwasher (pkg. 6) AF114 Replacement Bag (not shown) *See Separate Page for Exploded View Painted parts furnished in white unless otherwise specified Page 11 PADDLE ASSEMBLY FRONT PADDLE CLAMP ASSEMBLY - AF176 REAR PADDLE CLAMP ASSEMBLY - AF121 PADDLE ASSEMBLY Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 Part No. FG135 AF157 F218 F267 F240 FG443 FG450 F243 F237 F215 F197 F949 FG288 F489 Description Handle Weldment Trigger Release w/Rodhinge, Pin, "E" Rings Clamp Leaf Spring w/Hardware Pivot Pin w/"E" Rings Clamp Slide Supp. Pin Clamp Latch Rod Latch Pin Slide Spring Clip Clamp Slide Set Collar Spring Pin Pin "E" Rings Ref. No. 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Part No. FG277 F63 F11 F432 F433 AF165 AF168 F904 F842 F24 TU4787 F888 F901 FB187 Description Stud Springs w/Hardware (Set of 2) No. 11 Sleevers (Set of 2) Front Paddle Channel Sponge for Front Paddle Sponge for Rear Paddle Rear Paddle Channel Sponge Pad (Set 6/F842) Vent Clamp No. 24 Sleevers Hex Nut "E" Rings #10-24 x 3/8 Screw #10 Lockwasher Painted parts furnished in white unless otherwise specified Page 12 JACKET AIRE FORM JACKET Ref. AF120 AF117 PU47 AF152 AF102 AF104 AF103 AF144 FG344 TU8013 AF161 FG343 FG345 Description Gun Support Bracket Locating Plug Shaft Tube Cover Removable Air Filter Frame Weldment Filter Screen Jacket Weldment Speed Nut Cissell Nameplate Control Panel Assembly (See Separate Page) Screw w/Wear Washer Retaining Washer Painted parts furnished in white unless otherwise specified Page 13 PANEL CONTROL PANEL - AF161 Ref. FG235 FG234 FG453 AF185 AF162 AF100 PT118 C196 LB291 AF203 AF216 AF217 Description Relay - 115V/50-60 Hz. Timer - 115-230V Toggle Switch Panel Nameplate Timer Knob Set Screw #6-32 x 3/8 Rd. Screw Wiring Harness (not shown) Resistor, 200VL w/Piggy Back End & Black Insulation Resistor, 500VL w/Piggy Back End & Black Insulation Page 14 AIR FORM REAR BASE Ref. No. 1 2 3 4 5 6 7 8 9 Part No. FG274 SGV13 SGV40 AF124 SB170 PIU94 F739 F738 TU3549 FG175 Description 1/2" Pipe 30" Long Supply Valve Return Valve Rear Base Weldment Junction Box Cover Nameplate Solenoid - 115V Solenoid - 230V Rubber Bumper Rod Extension Ref. Remove wires from old switch and install wires on new switch and tighten securely. Reinstall switch, insulation, plate, washers and screws and tighten securely. [. . . ] Voltage phase and frequency must be the same as specified on machine nameplate. Check motor to see if it will operate on normal nameplate electrical power. Check to see if relay will operate on rated current and if contacts will carry current. If not, replace relay. 7C Air timer set at 0 time 7D Defective blower relay 7E Defective blower motor 7F Loose wires (8) (9) Blower motor won't start, machine steams continuously after air switch is operated. [. . . ]