User manual CISSELL CHMW35-WE55-165

[. . . ] Contents 1 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Technical data and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is however followed by a coast and tumble time to disentangle the linen. This special function prevents the user from opening the machine while the drum is still rotating and represents an important safety feature. To return to normal operation, press the START-button (S). During final spin, only the programmed low spin time will be completed as regular wash action. This function influences the cycle time - the program continues normally - and remains active until the START-button (S) is pressed. 17 4 End of a program At the end of a program, while the door is being released, the left display shows End; and the Start-LED is switched off. After that only the right display will continue to show the program number. This is the end of the program. Premature ending of the program By pressing the START-button (S) during the program, the Start-LED is switched off and the water is drained from the machine. As long as the water has not reached the safety level, the door will remain sealed and the display will show "SLE" (Safety Level) on the left display. Afterwards the display will temporarily show "End" on the same display and the Start-LED will be switched off. After that only the right display will continue to show the program number. This is the end of the program. Remark: If any attempt is made to interrupt the program prematurely during a spin phase of the program, all functions on the display will be temperary replaced by blinking horizontal dashes. After that only the right display will continue to show the program number and the door will be released. This is the end of the program. 18 4 Remarks: Freely programmable stop-function Before starting a program it is possible to preprogram a time stop in every program segment. This function permits special additional functions like adding bleach or extra detergent to the wash bath. Programming: After selecting the program, press the ECO-button (E) and keep it depressed. The left display now shows "StO" (Stop) and the right display shows the program number. Confirm by pressing the START-button (S) if a time stop is required in this phase of the program. If no time stop is needed, press the ECO-button (E) to move on to the next segment of the program. If needed, return to previous segments by pressing the SELECT-button (P). Errors can be corrected by returning to the erroneously programmed time stop in the segment and correcting by pressing the START-button (S). After the final program segment all programmed time stops will be displayed and the left display will show "End". Operation: When a stop is reached during the run of the program, the time will be stopped. The wash bath will be filled to the appropriate level and temperature and the programmed wash action is executed. [. . . ] B : Number of coin insertions COIN 1 (up to 60. 000) This parameter is only indicated if it has been programmed as such in the programmation (COIN COUNT). C : Number of coin insertions COIN 2 (up to 60. 000) This parameter is only indicated if it has been programmed as such in the programmation (COIN COUNT). D : Info manufacturer or technician TMP T/N : Info manufacturer or technician. Here you can program the temperature to appear on display in case this has not been done at the programmation. [. . . ]