User manual CISSELL CISSIMAN38

[. . . ] Cissi Form Finisher Models FCCG FCCD FCFG FCAC MANUAL OWNER'S MANUAL CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 MANUAL THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER. MAN38 5/97 Page 1 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. [. . . ] Recommend steaming, conditioning, drying the central position of the switch. Push the push-to-start switch or step on the foot switch and the cycle will automatically sequence. If you desire to cancel that cycle at any time, push the white switch toward the cycle off location. Page 10 CISSI FORM FINISHER The "Tower of Power" is at your fingertips for all of the finishing combinations you will ever need. All three timers (steaming, conditioning, drying) are adjustable from 0 to 30 seconds. The cycle switch provides (presteam only, steaming-conditioning-drying, steam & air-conditioning-drying) which ever is required. Place the net bag over the form so that it fully covers the standard nylon bag. Place the garment on the form and operate the machine per standard instructions, using "large size" setting for faster drying. In general, garments including bonded knits and wool dresses can be finished without the overbag. When ordering additional net overbags, specify F816. Page 12 CHANGING INSTRUCTIONS F833 Bag with GENIE Revolving Assembly TO REMOVE BAG TO REPLACE BAG (1) Remove yellow weights, 1 each side. (4) Replace yellow weights, one each side, on end of control strings. (2) Raise the lower control ring (inside bag). (3) Lower the control ring inside bag. (3) Open zipper and untie bottom string. (2) Tie bottom string in groove and close zipper. Straighten bag until control strings are at the sides. (4) Lift bag off over revolving assembly shoulder form. (1) Place bag over revolving assembly shoulder form, with front of bag toward front of form. Page 13 INSTRUCTIONS FOR TYING LOWER TIE STRING Page 14 CISSELL STEAM-AIR FINISHER INSTRUCTIONS FOR ADJUSTING HEIGHT REVOLVING OF REVOLVING FORM (Model FM** and Model FG2) Should the revolving form "drag" on the base rather than turn freely, the form must be raised. Conversely, if the revolving form hides too high above the base, permitting steam to escape from the space between the form and base, the form must be lowered. WHEN AN ADJUSTMENT MUST BE MADE, REMOVE REVOLVING FORM BY SIMPLY LIFTING IT STRAIGHT UP OFF THE BASE. Turn F287 Bearing Adjustment Screw COUNTER-CLOCKWISE. CHECK ADJUSTMENT: Replace revolving form on base. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too low. . . or too high. . . repeat adjustment until it is correct. Turn F287 Bearing Adjustment Screw CLOCKWISE. CHECK ADJUSTMENT: Replace revolving form on base. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too high. . . or too low. . . repeat adjustment until it is correct. Page 15 SOLENOID LINKAGE ADJUSTMENT TO ADJUST STEAM VALVE AND SOLENOID LINKAGE: 1. Set steam valve extension bar and solenoid lever at 90º as shown and tighten set screw. Adjust steam valve adjusting nuts until 1/32" to 1/16" gap is obtained as shown above and lock adjusting nuts tightly together. Page 16 MOT MOTOR MOUNTING DIMENSIONS Page 17 SERVICE CHART PROBLEM (1) No Steam CAUSE CAUSE 1A Steam Supply Valve "OFF" 1B Electric power"OFF" REMEDY Open valve in steam supply line. [. . . ] F149 FG320 F215 FG275 TU49 F539 TU4593 LB20 FG319 F357 FG321 FG322 FC1 Description Steam Valve Pull Rod Extension Bar Set Collar (2 Req'd. ) Steam Valve Lever Ass'y Delrin Bearing Stm. Chamber 1/2" x 90º Pipe Elbow 1/2" Pipe Nipple 3" Long Stm. Coil Adapter Felt Air Seal Steam Manifold Steam Coil Base Welded Ass'y Ref. Description See Separate Parts Sheet 1/4" - 28 Brass Nut 1/4" Lockwasher 1/16" x 1/2" Cottor Pin 3/8" x 1 1/4" Hex. [. . . ]