User manual CISSELL CSHW75-HF245-304

[. . . ] Contents 1 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Technical data and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] F2 = Soak To soak heavily soiled linen F3 = Reduced wash action To avoid wear of delicate garments F4 = Execute high spin as low spin To avoid creasing delicate linen F5 = Rapid advance To skip certain program segments F6 = No spin To give total protection to delicate garments F7 = on the left display appears the number of revolutions of the drum. Selecting a function Push the SELECT-button (P) at the time the special function needs to be activated and keep the button depressed. By pressing the SELECT-button (P) the next function will appear on the central display. To return to normal operation, press the START-button (S) and release. Functions are also automatically ended and switched off at the end of the each program. 13 Description of the functions Function F1 (Time stop) 4 During the wash cycle: The wash time is stopped. The temperature, water level and wash action remain the same as programmed. During the wash cycle, this function remains active until the START button (S) is pressed again. During intermediate spin : The intermediate spin normally lasts 1 minute. By activating function F1, the machine will spin for nine minutes unless the START button (S) is pressed earlier. By activating F1 during low spin, this low spin will be extended to15 minutes unless the START button (S) is pressed earlier. If the 15 minutes of low spin have been completed, the high spin is automatically canceled. By activating F1 after the preprogrammed low spin, you will have a maximum of 14 minutes of high spin unless the START button (S) is pressed earlier. When this time is expired, the function will appear automatically and the program will continue. From now onwards, "F1" and "10" appear by turns on the middle display. By pressing the ECO button (E) once more, you add each time 10 minutes. By means of the START button (S), you can each time reduce 10 minutes. Remark : The programmed stop time is executed after the decimal point in the right display has extinguished. Function F2 (soak) This function can only be chosen during prewash, main wash and first rinse. The bath is filled till high water level and heated up to 40 °C (if a higher temperature was programmed, this will be followed). As long as this temperature is not reached, the machine makes a reduced wash action ( shorter action time and longer pause time). When the bath has reached its temperature, the drum will make one left/right rotation every 4 minutes. Should the temperature fall, the water will be heated again, during which the action will be reduced again. This function remains active until the START button (S) is pressed again. [. . . ] Program 0 (starching) is mostly used in very special applications and is therefore not displayed on the front panel. 0. CURTAINS 1 RINSE 2 BATHS 1 BATH 2 BATHS 1 BATH 2 BATHS 1 BATH 2 BATHS 1 BATH 1 BATH COLD 40°/90°C 90°C 40°/60° 60°C 40°/40°C 40°C 30°/30°C 30° COLD 19 Technical remarks Internal connections of the electrical heating Heating 18kW 3x3kW 3x3kW 3x3kW 3x4kW 3x4kW 3x4kW 3x5kW 3x5kW 3x220V R5 LC1D323 3x380V R5 LC1D1810 21kW ------------------------------- ------------------------------- LC1D1810 LC1D1810 LC1D1810 LC1D1810 LC1D1810 LC1D1810 24kW 30kW B = Black Gy = Grey R = Red PU = Purple Y/Gr = Yellow/green Br = Brown Bu = Blue W = White W/B = White/black W/R = White/red Remark: Other executions are available as options. Tilt switch Window The tilt switch is mounted on the solid part of the machine. There is a window around the probe of the tilt switch that is mounted on the movable part of the machine. When the machine goes out of balance by overloading or uneven distribution of the linen, the tilt switch will interrupt this action to prevent damage to the machine. Important Probe To guarantee good functioning, the probe should be centered horizontally and vertically at 1/3 from the bottom of the tilt window (when machine drum is empty). 20 6 Error messages When one of the following malfunctions occurs during a program, the central display will communicate the appropriate error message at the end of the cycle. [. . . ]