User manual CISSELL GENIEMAN59

[. . . ] With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. The liability of Cissell does not include furnishing (or paying for) any labor such as that required to service, remove or install; to diagnose troubles; to adjust, remove or replace defective equipment or a part; nor does it include any responsibility for transportation expense which is involved therein. [. . . ] Air will operate continously until OFF Air switch is pressed. Page 6 Fig. 2 Page 7 OPERATING OPERATING INSTRUCTIONS CAUTION: Timer Adjustments STEAM: Must not be greater than 6 seconds (Average setting 4-5 Seconds) AIR: Must not be less than 20 seconds (Average Setting 25 Seconds) NOTE: Straighten Pockets; Button Pocket Flaps; Button or Snap front of Waist Band, But Do Not Close Zipper. Grip rear top portion of bag and puff waist expander forward until it locks. Lift trousers onto form, placing back center of waist band high onto waist expander. Continue to hold forward tension on trousers and push "bag release" knob. Allow automatic tension of waist expander to draw front of trousers onto face of buck. Align crotch; do not raise pants too high as crotch must remain loose in buck opening to prevent wrinkling of crotch area. To soften pleats (Before making respective pleat lays), push PRE-STEAM BUTTON. This may be minimized by using "air" while steaming; or shortening of steam cycle by depressing fully "off " air switch. Do not use the pre-steaming operation on rayon acetates. 4. 5. 6. Smooth out material and lay each pleat separately, working from fly toward pleat being layed. If too much material is encountered during laying of pleats, trousers are too high on the buck and too low on the rear expander. In operation, bag collects dust, lint, etc. , greatly reducing its efficiency. Launder bag at frequent intervals as determined by its soiled condition. The Cissell Pants Topper bag has a double liner to extend pad life and to distribute steam uniformily. REPAIR HOLES OR WORN SPOTS in bag to extend its useful life: REPLACE when worn beyond repair. A defective or worn bag will cause topper to operate unsatisfactorily. KEEP A SPARE BAG IN STOCK. CAUTION CAUTION Use only genuine CISSELL PT474 bags. The fabric for the Cissell Bag is especially woven (and cut to an exact pattern) to give the correct porosity and shape for proper steaming and drying. Remember, your CISSELL PANTS TOPPER depends on the bag for proper operation. Correct padding is necessary to obtain proper finishing. The Cissell buck pad is constructed of a high, heat-resisting synthetic air foam, and perforated for rapid steaming and full air flow through entire buck area. Do not use more than 1 pad. RESEALING EDGES FOR STEAM & CONDENSATE CONDENSATE LEAKS When leak appears: 1. Using sealing compound Permatex #2 or equilvalent; Generally apply sealing compound evenly along area of "Leak". [. . . ] Eliminate loop or install a by-pass trap from lowest point of loop or fall Install a by-pass trap header to drain off condensate before reaching supply inlet. Inspect traps of all machines to determine whether one or more traps are standing open; or whether another trap is discharging towards return line connection of Pants Topper. Correct trap installations and perform steps necessary to eliminate back pressure in return line. Return line must drain by gravity to condensate return tank; and return tank must be adequately vented. [. . . ]