User manual CISSELL MANCONS

[. . . ] The warranty is void on equipment or parts; that have been subjected to misuse, accident, or negligent damage; operated under loads, pressures, speeds, electrical connections, plumbing, or conditions other than those specified by Cissell; operated or repaired with other than genuine Cissell replacement parts; damaged by fire, flood, vandalism, or such other causes beyond the control of Cissell; altered or repaired in any way that effects the reliability or detracts from its performance, or; which have had the identification plate, or serial number, altered, defaced, or removed. No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization from Cissell. Charges for unauthorized repairs will not be accepted or paid by Cissell. CISSELL MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, STATUTORY OR OTHERWISE, CONCERNING THE EQUIPMENT OR PARTS INCLUDING, WITHOUT LIMITATION, A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, OR A WARRANTY OF MERCHANTABILITY. [. . . ] (113 kg) 61" x 25" x 69" (155 cm x 64 cm x 175 cm) 61 Cubic Feet (1. 73 m 3) Maximum Operating Pressure Boiler Horsepower Required Steam Supply & Return Lines Net Weight Shipping Weight Export Shipping Dimensions Export Crate Volume 100 P. S. I. (113 kg) 61" x 25" x 69" (155 cm x 64 cm x 175 cm) 61 Cubic Feet (1. 73 m 3) Page 3 INSTALLATION INSTRUCTIONS NOTE: This machine should be installed by qualified service personnel only. 1. Check the nameplate voltage and current; match it with the power being connected. NOTE: Before final return line connection is made, open the steam supply valve and blow all foreign matter out of the steam lines. Make electrical connections in junction box on rear of machine, following applicable electric codes. Include a fused disconnect switch or circuit breaker with slow-blow characteristics and be capable of carrying 15 amps, 115 volts or 8 amps, 230 volts. Test the machine, following the OPERATING INSTRUCTIONS in this manual. Page 4 SAFETY PRECAUTIONS Please read these warnings before operating or servicing machine. CAUTION: Shut off electrical supply before servicing to avoid electrical shock. Cissell form requires adjustment of the Waist, Hip and Lower control knobs. Press the AIR foot switch to operate the blower for sizing the form bag. Using the Control Panel, press the MODE SELECT until the AIR light glows and press START/CANCEL to operate the blower, then proceed with sizing the bag. Set the three control timers to the recommended settings: Steaming: 6-9 seconds Conditioning: 4-9 seconds Drying: 12-16 seconds These settings should be fine-tuned to the particular garment, steam pressure and ambient conditions. This machine has the ability to pre-steam a garment prior to the automatic finishing cycle. To actuate this cycle, press the MODE SELECT pad until the PRE-STEAM LIGHT glows, then press START. If a cycle is operating, it can be cancelled at any time by pressing any foot switch or control panel pads. Control Panel Page 5 OPERATION - CONTROLS Page 6 SERVICE CHART CAUTION: BEFORE SERVICEING MACHINE, SHUT OFF ELECTRICAL POWER TO AVOID POSSIBLE ELECTRICAL SHOCK. SHUT OFF STEAM SUPPLY AND PURGE PRESSURE FROM STEAM LINES TO AVOID BURNS FROM HOT STEAM. REFER TO PARTS SHEETS FOR CORRECT REPLACEMENT PARTS. (1) No Steam PROBLEM A. Steam timer may slip on shaft and be set on 0. (2) No Air See A. Check for blown fuse, tripped circuit breaker or loose wire connection. [. . . ] FG277 FG288 F435 F434 F901 F842 F904 F24 F11 ET183 F888 F122 F950 F489 TU4787 FB187 Description Stud Pin (3/8) Sponge (24) Paddle Channel (24) #10 - 24 x 3/8 Hex. Screw* Vent Clamp Sandpaper & Sponge Set for F842 #24 Sleever #11 Sleever E Ring for 1/8 Pin* E Ring for 3/16 Pin* 1/4 - 28 Brass Nut 3/8 Cut Washer* E Ring for 3/8 Rod* 3/8 - 16 Hex Nut* #10 Split Lockwasher* 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Page 20 STEAM COLUMN & PIPING PARTS Ref. F1227 F1269 F286 F287 F542 F1292 390401016 F1289 F1296 F1394 F1397 F894 IB139 VSB134 IB140 F1449 Description Steam Chamber Column Bearing Support Frame Bearing Locknut Bearing Adjustment Screw Pipe Plug Union 3/8 x 2 Pipe Nipple Solenoid Valve Steam Nozzle Steam Spreader Pipe Nipple (3/8 x close) Drawband 3/8 - 16 x 1-1/4 Bolt 3/8 Lockwasher 3/8 Flat Washer Connector Flare Ref. 17 18 19 20 22 23 24 25 26 27 29 30 31 Part No. Description F1456 Coil Supply Tube Assy (CF100) F1458 Coil Supply Tube Assy (CF600) F1324 Steam Coil (CF100) F1288 Steam Coil (CF600) F1399 1/4 - 20 x 1 Screw (see page 19) 400518040 Insulation (order by length) FG143 Pipe Tee SC196 Pipe Weldment SC505 Coupling F1461 Elbow w/Fitting F1439 Condenser F896 Drawband Eye F1457 Coil Return Tube Assy (CF100) F1459 Coil Return Tube Assy (CF600) F1448 Column Supply Tube Assy Page 21 Ref. [. . . ]