User manual CISSELL PANTOPBMAN309

[. . . ] Page 1 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. [. . . ] A defective or worn bag will cause topper to operate unsatisfactorily. KEEP A SPARE BAG IN STOCK. CAUTION CAUTION Use only genuine CISSELL bags. The fabric for the Cissell Bag is especially woven (and cut to an exact pattern) to give the correct porosity and shape for proper steaming and drying. Rember, your CISSELL PANTS TOPPER depends on the bag for proper operation. Correct padding is necessary to obtain proper finishing. The Cissell buck pad is constructed of a high, heat-resisting synthetic air foam, and perforated for rapid steaming and full air flow through entire buck area. Do not use more than 1 pad. RESEALING EDGES FOR STEAM & CONDENSATE LEAKS CONDENSATE When leak appears: 1. Generously apply sealing compound evenly along area of "Leak". If necessary, remove switches from control box in Nose, when fixing leaks in this area. Page 15 PLEAT ASSEMBLY INSTALLA ALLATION PLEAT SETTER COVER ASSEMBLY INSTALLATION 1. Place cover over pleat clamp (E), pull draw strings (K) tight and tie. Hook one end of each pleat clamp spring (M) on left side of cover, pull tight and hook on right side. Adjustable Clamp Support OVAL PLEAT ADJUSTABLE OVAL PLEAT CLAMP ADJUSTMENT WITH ADJUSTABLE CLAMP SUPPORT REFER TO ILLUSTRATION ABOVE. Loosen cap screw (A) in arm expander and cap screw (B) in adjustable support. Rotate and slide arm (C) in counterweight (D) to position pleat clamp (E) on buck. Place pleat clamp in vertical position and align inside edge of pleat clamp with edge of buck crotch (F). Apply pressure on arm knob (G) to provide pressure between pleat clamp (E) and buck. With a thin card (H) check uniformity of pressure between edges of pleat clamp (E) and buck. If unequal, rotate pleat clamp slightly to obtain a uniform pressure around all edges. Note: Whenever tightening nut (B), do not apply pressure to knob (G) or arm (C), as this will distrub the pleat clamp setting. If pleat clamp (E) makes an impression (too tight), loosen cap screw (B) and rotate adjustment nut (J) counter-clockwise to reduce pressure. If pleat clamp does not hold pleat (too loose), loosen cap screw (B) and rotate adjustment nut (J) clockwise to increase pressure. Retighten cap screw (B). 2. 3. 4. 5. 6. B. NOTE: Each pleat clamp must engage the padded buck uniformily with a slight pressure. A very light pressure may allow pleat lay to shift during the air cycle, and show wrinkles with an improperly shaped pleat. Adequate holding of the pleat lay during the air cycle is aided by the surface texture of the pleat clamp and the buck cover. Page 16 PLASTIC SLEEVE, BEARING ADJUSTMENT PLASTIC SLEEVE POSITION AND TAPING FIG. [. . . ] (11) TIMED STEAM - BUT, NO TIMED AIR When automatic pushbutton is operated NOTE: Timed air is obtained after timed steam, by holding the automatic pushbutton operated 10a. Holding circuits for relays SR and AR open, defective wire terminal connections on the dark blue wire extending from the pre-steam pushbutton to the terminal block in control box 10b. Holding circuit for steam relay SR open at contact (relay SR), and the holding circuit for relay AR open at contacts (automatic relay AR) or (air timer AT) 11a. Holding circuit for automatic relay AR open at contact (air timer AT) 11c. [. . . ]