User manual CLARION BD216

[. . . ] CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5. OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8. ERROR DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 10. SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 English s Table des matières Français 1. [. . . ] to remove roughness from the edge of the disc. Ball-point pen Roughness Do not use any solvents such as commercially available cleaners, anti-static spray, or thinner to clean compact discs. No Do not use compact discs that have large scratches, are misshapen, or cracked, etc. Use of such discs will cause misoperation or damage. No Do not expose compact discs to direct sunlight or any heat source. No Note: · Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may get caught in the internal mechanism and damage the disc. 6 BD216 6. DCP (Detachable Control Panel) The control panel can be detached to prevent theft. We recommend taking the DCP with you when leaving the car. CAUTION · The DCP can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. · When the release button is pressed and the DCP is unlocked, the car's vibrations may cause it to fall. To prevent damage to the DCP, always store it in a protective case after detaching it. · The rear connector that connects the source unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. DCP Rear Panel Source Unit Front Removing the DCP 1. Remove the DCP. DCP connector Source unit connector Note: · If the DCP is dirty, wipe off with a soft, dry cloth only. DCP Attaching the DCP 1. Insert the left side of the DCP into the main unit. CAUTION Do not insert the DCP from the left side. OPERATION Note: · Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold). Basic Operations CAUTION When this unit is turned on, starting and stopping the engine of a car with its volume raised to the maximum level may harm your hearing. Be careful about adjusting the volume. Adjusting the Treble 1) Press A-M button @ and select "TrE". 2) Turning the Rotary knob 2 clockwise emphasizes the treble; turning it counterclockwise attenuates the treble. * The factory default setting is "0". (Adjustment range: ­6 to +6) Turning ON the Power and Adjusting the Volume 1) Press the POWER button 4. 3) When the adjustment is complete, press A-M button @ several times until the function mode is reached. English * To turn off the power, press the POWER button 4 for 1 second or longer. Adjusting the Balance 1) Press A-M button @ and select "BAL". 2) Turning the Rotary knob 2 clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left speaker. 2) Press the FNC button 4 and select another operation mode. Every time the FNC button 4 is pressed, the display changes the operation mode as: Radio § CD § Radio Note: * The factory default setting is "0". (Adjustment range: L9 to r9) · If the CD mode is selected when no disc is inserted, the display flashes " DISC" and blinking. 3) Turning the Rotary knob 2 clockwise increases the volume; turning it counterclockwise decreases the volume. 3) When the adjustment is complete, press A-M button @ several times until the function mode is reached. * The volume level is from 0 (minimum) to 33 (maximum). Adjusting the Fader 1) Press A-M button @ and select "FAd". 2) Turning the Rotary knob 2 clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers. Audio Mode Adjustments Press the A-M button @ to select the adjustment mode. The mode switches as follows each time the A-M button is pressed: BASS § TREB § BAL § FAD § Previous mode * The factory default setting is "0". [. . . ] ERROR DISPLAYS s To protect the system, this unit has been equipped with self diagnostic functions. Error Display Corrective Measure This error display indicates that a fault has arisen in the mechanism of the source unit (for example, the disc cannot be ejected). This error display indicates that the pickup focus is off because of a scratched disc or some other factor during source unit play. § Check the compact disc. Er 2 Er 3 Er 6 E glis This indicates that the CD's TOC (table of contents) cannot be read, for example because the selected disc is upside-down. BD216 13 10. [. . . ]