User manual CLARION CDC1255Z INSTALLATION MANUAL

[. . . ] THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE. 50 KAMITODA, TODA-SHI, SAITAMA-KEN, JAPAN. Y-adapter (Brack) (Brack) (Gray) Ferrite clamp (Horizontal Position) 4. Remove the separator of the cushion rubber that is attached to the installation bracket with bolt and install accordingly. Unfasten the wing nut and remove the unit. , , , , , , , , , , 1. Be sure to use the screws, etc. , included in the package tor installation. Using other screws could damage the set. [. . . ] q When the inside of the car is very cold and the player is used soon after switching on the heater, dew may form on the disc or optical parts of the player and proper playback may not be possible. If dew forms on the optical parts of the player do not use the player for about one hour and the condensation will disappear naturally to allow normal operation. While the system is in play, do not plug or unplug the cables as this will cause damage. Do not expose the magazine to direct sunlight, the car heater or other sources of strong heat. Replace the CD magazine (CAA-122) with a new one if bent or otherwise damaged. Caution · ONLY use the magazine included with the CDC1255z or RDC1255z. Do not attempt to insert different style magazine into the CD changer even if they fit into the magazine opening. Inserting other manufacturers' magazines or previous Clarion 6 Pack style magazines into the CDC1255z or RDC1255z will cause damage to the mechanism and void the warranty. Label Side One in each slot (6 pieces) 15° 30° 45° 15 ° 3 CAUTIONS ON HANDLING CDs mark. Use only compact discs bearing the Do not play heart-shaped, octagonal, or other specially shaped compact discs. Use a ball-point pen, etc. , to remove roughness from the edge of the disc. Ball-point pen Roughness q Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. Storage q Do not expose compact discs to direct sunlight or any heat source. q Do not expose compact discs to direct heat from heaters. q Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. q Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player. Never touch the surface. Cleaning q To remove fingermarks and dust, use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference. q Do not use any solvents, such as commercially available cleaners, anti-static spray or thinner to clean compact discs. q After using special compact disc cleaner, let the compact disc dry off well before playing it. H <Example of address switch setting> q Setting example 1 Source unit CD changer CeNET wire bound 2 Address switch number 2 CD changer 1 Address switch number 1 Important Important 7 · INSTALLATION OF CONNECTORS CeNET cable Be sure that the CD changer numbers are not the same. Note: Only the provided screws and brackets should be used during installation. Align the unit with the bolts and secure it with the wing nuts. q Setting example 2 Source unit CD changer When the CeNET cable is connected, it must be inserted fully and securely. After connecting, fasten the cable using the cable holder or cable clamp. When removing the digital optical fiber cable, rotate it to loosen it and pull it gently while holding the slide cap (a gray color part on the source unit). Do not coil up the digital optical fiber cable with a radius of less than 1" (3 cm). With a radius of less than 1", the performance of the cable will be greatly impaired. When installed in a glove box or console box, make sure that the source unit cables or cords do not interfere with the opening or closing of the slide door. Slide cap Digtal optical fiber cable 1 Address switch number 1 Important Do not use address switch numbers "3' or "4'. · MD changer CeNET wire bound 1 Address switch number 1 · · Caution · The unit may not operate when both CD changers are set to the same address switch number. [. . . ] The unit installation direction and the installation selector lever positions do not match. Set the unit installation direction and the installation selector lever positions to match each other. When installed at an angle, change the installation selector lever to a position (H, 45, V) not prone to noise or sound loss. 2. (3. 3kg) : 10. 6"(Width) × 3. 9" (Height) × 6. 7"(Depth) [268mm(W) × 98mm(H) × 170(D)mm] 2. [. . . ]