User manual CLARION DB166

[. . . ] Please read this owner's manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e. g. , glove compartment). Check the contents of the enclosed warranty card and keep it carefully with this manual. English Contents 1. FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car. English Storing the DCP in the DCP Case Hold the DCP, in the orientation as shown in the figure below, and put it into the supplied DCP case. (Ensure the DCP is in the correct orientation. ) Removing the DCP 1. Press the [SRC] button for 1 second or longer to switch off the power. Press in the [RELEASE] button. [RELEASE] button DCP DCP case CAUTION · The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks. · When the [RELEASE] button is pressed and the DCP is unlocked, the car's vibrations may cause it to fall. To prevent damage to the DCP, always store it in its case after detaching it. (See figure above. ) · The connector connecting the main unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. DCP Rear Panel Main Unit Front The DCP is unlocked 3. Insert the left side of the DCP into the main unit. 2. DCP connector Main unit connector Note: · If the DCP is dirty, wipe off the dirt with a soft, dry cloth only. DCP 1. DB166 7 6. OPERATIONS Basic Operations CAUTION Be sure to lower the volume before switching off the unit power or the ignition key. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and damage the unit. Note:Be sure to read this chapter referring to the front diagrams of chapter "2. CONTROLS" on page 3 (unfold). English Setting the Z-Enhancer This unit are provided with 3 types of sound tone effects stored in memory. Select the one you prefer. The factory default setting is "Z-EHCR OFF". Turning on/off the power Note: · Be careful about using this unit for a long time without running the engine. If you drain the car's battery too far, you may not be able to start the engine and this can reduce the service life of the battery. Each time you press the [Z] button, the tone effect changes in the following order: "Z-ENHANCER 1" (bass emphasized) "Z-ENHANCER 2" (treble emphasized) "Z-ENHANCER 3" (bass and treble emphasized) "Z-EHCR OFF" (no sound effect) "Z-ENHANCER 1". . . Audio Mode Adjustments 1. The mode switches as follows each time the [A-M] button is pressed: BASS TREB BAL FAD Previous mode When the Z-Enhancer function is turned on, BASS (bass) and TREB (treble) cannot be selected. 2. The unit automatically remembers its last operation mode and will automatically switch to display that mode. Press and hold the [SRC] button for 1 second or longer to turn off the power for the unit. Selecting a mode 1. Each time you press the [SRC] button, the operation mode changes in the following order: Radio mode CD mode Radio mode. . . Note: · If the CD mode is selected when no disc is inserted, the display shows "NO DISC". 2. [. . . ] Press the [ISR] button again to return to the previous mode. Ejecting a CD 1. Note: · If you force a CD into before auto reloading, this can damage the CD. If a CD (12 cm) is left in the ejected position for 15 seconds, the CD is automatically reloaded (Auto reload). Each time you press the [] button, the track advances ahead to the beginning of the next track. 10 DB166 CD Operations English GTrack-down 1. Press the [å] button to move back to the beginning of the current track. [. . . ]