User manual CLARION DB415

[. . . ] When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the optical parts of the player, do not use the player for about one hour and the condensation will disappear naturally to allow normal operation. Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. [. . . ] · The connector connecting the unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc. 3. Pull the DCP toward you and remove it. DCP Note: · If the DCP is dirty, wipe off the dirt with a soft, dry cloth only. 4. Close the HOLD FLAP. HOLD FLAP CAUTION Be sure to close the HOLD FLAP for safety when removing the DCP. DB415 7 7. REMOTE CONTROL If you buy the RCB-130, sold separately, you can enjoy the use of the remote control function. Receiver for remote control unit Operating range: 30° in all directions Remote Control Unit Signal transmitter English & ( ¡ ) * £ TM § ¢ ¶ Inserting the Batteries 1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. Insert the AA (SUM-3, IECR-6/1. 5V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover. AA (SUM-3, IECR-6/1. 5V) Batteries Notes: Using batteries improperly can cause them to explode. Take note of the following points: · When replacing batteries, replace both batteries with new ones. · Dispose of spent batteries properly. Rear cover Rear side 8 DB415 Functions of Remote Control Unit Buttons Mode Button & FUNC * BAND DISC UP PROG TOP ( VOLUME ) SEARCH Radio CD Turns power on and off. Switches between playback and pause. ¡ PLAY/PAUSE TM MUTE £ ISR Turns mute on and off. Press and hold for more than 2 seconds: Stores current station into ISR memory (radio mode only). Scan play. ¢ DISP SCAN PS/AS § RPT BLS ¶ RDM MONI Repeat play. Random play. * Some of the corresponding buttons on the source unit and remote control unit have different functions. DB415 9 8. OPERATION Note: · Be sure to read this chapter referring to the front diagrams of chapter 2. 2) Turning the Rotary knob # clockwise emphasizes the bass; turning it counterclockwise attenuates the bass. Setting the Z-enhancer This unit comes with three types of sound tone effects stored in memory. Each time you press Z-EHCR button 0, the tone effect changes in the following order. "Z-ENHANCER 1" § "Z-ENHANCER 2" § "Z-ENHANCER 3" § "Z-EHCR OFF" § "Z-ENHANCER 1". . . · Z-ENHANCER 1: bass emphasized · Z-ENHANCER 2: treble emphasized * The factory default setting is "Z-EHCR OFF". * The factory default setting is "0". (Adjustment range: ­6 to +6) 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. 10 DB415 · Z-ENHANCER 3: bass and treble emphasized · Z-EHCR OFF: no sound effect Radio Mode Operations FM Reception ® For enhanced FM performance the tuner includes signal actuated stereo control and Multipath noise reduction circuits. Loudness Effect In order to turn on/off the loudness effect, use the LD button 2 for 1 second or longer. Every time the LD button 2 is pressed and held for 1 second or longer, the loudness effect switches on and off. Listening to the Radio 1) Press the FNC button 3 to select the radio mode, then the radio will be on. 2) To select a preset band, press the BND button !, then select one of the preset bands such as FM1, FM2, FM3, or AM. is pressed, the display will change as: FM1 § FM2 § FM3 § AM § FM1 3) Press the SRCH Left/Right button @, then the station at which there is a broadcast will be selected (Seek selection). * When the loudness effect is on, the display will show "LD". E glis Switching the Display Every time the DISP button 5 is pressed, the display will change between the main display and the clock display. Main display Clock display Mute Use this function to turn off the sound immediately. [. . . ] When this button is pressed again, the CD will play from the previous track. Listening to the Disc already Inserted Press the FNC button 3 to select the CD mode, the CD will start playing. Fast-Forward and Fast-Backward Press and hold the SRCH Left/Right button @. : To fast-forward : To fast-backward Stopping (pausing) Playback Press the Play/Pause button $. Press the Play/Pause button $ again to resume playback. * Pressing the SRCH Left/Right button for 1 second or longer will move forward or backward 5 times faster than normal play, and pressing it for 3 seconds or longer will do the operation 30 times faster. DB415 13 Scan Play (Intro Music Scan) Press the SCN button 8, then the display shows "SCN", then the CD will play the first 10 seconds of each track of the whole disc. Press the SCN button 8 again to disengage the unit from scan play. Repeat Play Press the RPT button 7, then the display shows "RPT", then the track currently playing will be played repeatedly. [. . . ]