User manual CLARION DPH910 INSTALLATION MANUAL

[. . . ] Owner's manual Mode d'emploi Manual de instrucciones Thank you for purchasing the Clarion DPH910. Please read this owner's manual in its entirety before operating this equipment. Check the contents of the enclosed warranty card and keep it carefully with this manual. For the operating instructions, refer to the owner's manual of the source unit. Contents 1. [. . . ] INITIAL DELAY: Adjusts the distance between sound source and reflecting surfaces. REAR MIX: Adjusts the ratio of the direct sound output from the rear speaker. · The settings for the basic DSF menus and the adjustment ranges are shown in the following table. About the sound field system The DPH910 divides the sound field into three systems: reverberation, early-reflection and B. G. M. The reverberation system is the part of the sound field where reverberating sound is vivid, while the early-reflection system is the part of the sound field where reflected sound is emphasized. · The different car types and the speaker installation positions are as follows: Vehicle type 1. MIN VAN front: FULL rear: Equivalent to rear door · The settings of the basic P. EQ menus are as follows: BAND 2 2kHz/F, 1/Q, -4dB/G 1. 25kHz/F, 5/Q, 0dB/G 800Hz/F, 3/Q, -4dB/G 125Hz/F, 5/Q, -12dB/G 1kHz/F, 3/Q, -8dB/G 800Hz/F, 1/Q, -8dB/G 500Hz/F, 5/Q, -5dB/G 1. 25kHz/F, 3/Q, -4dB/G 630Hz/F, 3/Q, -4dB/G 1. 25kHz/F, 3/Q, -8dB/G 500Hz/F, 5/Q, -5dB/G BAND 3 5kHz/F, 1/Q, -4dB/G 8kHz/F, 5/Q, 0dB/G 8kHz/F, 1/Q, -5dB/G 1. 25kHz/F, 5/Q, 0dB/G 10kHz/F, 1/Q, -6dB/G 8kHz/F, 5/Q, 0dB/G 1. 6kHz/F, 3/Q, 0dB/G 2kHz/F, 7/Q, +3dB/G 8kHz/F, 5/Q, 0dB/G 80Hz/F, 3/Q, +3dB/G 8kHz/F, 5/Q, 0dB/G 1. SEDAN Parametric Equalizer Parameter Channel Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear BAND 1 250Hz/F, 3/Q, -8dB/G 250Hz/F, 3/Q, -10dB/G 250Hz/F, 7/Q, -10dB/G 80Hz/F, 7/Q, +3dB/G 250Hz/F, 3/Q, -8dB/G 250Hz/F, 3/Q, -8dB/G 250Hz/F, 7/Q, -8dB/G 125Hz/F, 3/Q, -8dB/G 125Hz/F, 5/Q, -4dB/G 250Hz/F, 1/Q, -6dB/G 250Hz/F, 3/Q, -4dB/G 250Hz/F, 3/Q, -8dB/G 400Hz/F, 7/Q, -10dB/G 1. 25kHz/F, 7/Q, -8dB/G F; Center frequency (Hz), Q; Q curve, G; Gain(dB) 8 DPH910 Professional-mode functions <P. EQ (Parametric Equalizer) functions> Editing the P. EQ menus You can compensate for the frequency characteristics using the basic P. EQ according to your car type. · The P. EQ adjustment contents are as follows: Channel selection Select the channel to be compensated (front or rear). Selection of center frequency Select the center frequency that you want to compensate from the range of 20Hz to 20kHz. (1/3 octave step, 31 points) Selection of Q-curve Set the sharpness of the Q-curve to one of the parameters: 1, 3, 5, 7 and 20. Gain adjustment Adjust the gain (output level) in the range of 12dB to +12dB. (1dB step, 25 points) About the compensation of frequency characteristics See Figure 1 concerning the relationship of the center frequency, Q-curve (Q) and gain. Level (dB) Q curve (Q) F Q= f P. EQ memory (User memory) You can store 6 frequency characteristics into the memory, which are edited on the basis of the basic P. EQ menus. Gain (G) f 3dB Frequency curve Center frequency (F) Frequency (Hz) Figure 1 About the Q-curve (Q) For the Q-curve (Q), setting larger values makes the curve sharper, setting smaller values makes the curve flatter. (Figure 2) Selecting the Q-curve (Q) opposite to the frequency curve to be compensated makes the frequency characteristics flat. Q curve (Q) High Low Q curve; 20 Q curve; 1 Figure 2 DPH910 9 5. Before starting, be sure to disconnect the battery's negative "-" terminal to prevent accidents due to short-circuits. Location Consider safety and operability when selecting a place for installation. Avoid the following. · Locations where the unit will hamper driving. · Locations where the unit could injure passengers if the car stops suddenly. · Locations exposed to direct sunlight or hot air from the heater, etc. · Locations where the unit may be exposed to rain or water. 3. Screws other than those supplied could damage the unit. Case Case Damage 8mm max. 4. When drilling holes in the dashboard, etc. , be sure to check beforehand that there are no harnesses or other wires on the inside. Installation example (Installing the unit under the driver's seat) Note: Please read this chapter referring to "2. Attach the mounting brackets 5 to the sides of the DPH910 using the screws 8 provided. [. . . ] 9 RCA cable Using this cable, connect the DPH910 to the 2-channel power amplifier for the subwoofer speaker. Rear speakers @ Subwoofer speakers # RCA cable for front/rear line in Connect this cable to the DPH910. Note: · The longest wiring length of the CeNET cable is less than 65. 62ft (20m). When you connect the CeNET cable, be careful not to exceed the wiring length of 65. 62ft (20m). DPH910 13 8. [. . . ]