User manual CLARION DRX5675

[. . . ] ESPECIFICACIONES Sintonizador de FM Game de frecuencias: 87, 9 MHz a 107, 9 MHz Sensibilidad útil: 11 dBf Sensibilidad a 50 dB de silenciamiento: 17 dBf Selectividad de canal alternativo: 75 dB Separación estéreo (1 kHz): 35 dB Respuesta en frecuencia (±3 dB): 30 Hz a 15 kHz Generales Tensión de alimentación: 14, 4 V CC (permisible de 10, 8 V a 15, 6 V), negativo a masa Consumo de corriente: Menos de 15 A Impedancia de los altavoces: 4 (permisible de 4 a 8 ) Peso: 3, 97 lb. (1, 8 kg) Dimensiones: 7" (178 mm) de anchura × 2" (50 mm) de altura × 6" (152 mm) de fondo 7" (178 mm) 6" (152 mm) 2" (50 mm) Owner's manual Mode d'emploi Manual de instrucciones 1. When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the optical parts of the player, do not use the player for about one hour and the condensation will disappear naturally to allow normal operation. [. . . ] Note: DCP connector Source unit connector Attaching the DCP Insert the DCP into the right side of the source unit and press the left side to lock it. · If the DCP is dirty, wipe off with a soft, dry cloth only. CAUTION Do not insert the DCP from the left side. Doing so may damage it. Storing the DCP in the DCP Case Hold the DCP, in the orientation as shown in the figure below, and put it into the supplied DCP case. REMOTE CONTROL Receiver for remote control unit Operating range: 30° in all directions Remote Control Unit English Signal transmitter ¥ * ) ( & TM ¡ ¢ £ § Inserting the Batteries 1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. Insert the AA (UM-3/1. 5 V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover. Be careful about adjusting the volume. Adjusting the Treble 1) Press A-M button 2 and select "TREB". 2) Turning the Rotary knob $ clockwise emphasizes the treble; turning it counterclockwise attenuates the treble. * The factory default setting is "0". (Adjustment range: ­6 to +6) Turning ON the Power and Adjusting the Volume 1) Press the POWER button 3. 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. English * To turn off the power, press the POWER button 3 for 1 second or longer. Adjusting the Balance 1) Press A-M button 2 and select "BAL". 2) Turning the Rotary knob $ clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left speaker. 2) Press the FNC button 3 and select another operation mode. Every time the FNC button 3 is pressed, the display changes the operation mode as: Radio CD CD changer Radio Notes: * The factory default setting is "0". (Adjustment range: L9 to R9) · The operation mode not connected to the unit will not · be selected. If the CD mode is selected when no disc is inserted, the display flashes " DISC". 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. 3) Turning the Rotary knob $ clockwise increases the volume; turning it counterclockwise decreases the volume. Adjusting the Fader 1) Press A-M button 2 and select "FAD". 2) Turning the Rotary knob $ clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers. * The volume level is from 0 (minimum) to 33 (maximum). Audio Mode Adjustments Press the A-M button 2 to select the adjustment mode. The mode switches as follows each time the A-M button is pressed: BASS TREB BAL FAD Previous mode * The factory default setting is "0". (Adjustment range: F9 to R9) 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. Adjusting the Bass 1) Press A-M button 2 and select "BASS". 2) Turning the Rotary knob $ clockwise emphasizes the bass; turning it counterclockwise attenuates the bass. * The factory default setting is "0". (Adjustment range: ­6 to +6) 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. 10 DRX5675 Setting the Z-enhancer This unit comes with three types of sound tone effects stored in memory. Each time you press Z-EHCR button !, the tone effect changes in the following order. "Z-ENHANCER 1" "Z-ENHANCER 2" "Z-ENHANCER 3" "Z-EHCR OFF" "Z-ENHANCER 1". . . · Z-ENHANCER 1: bass emphasized · Z-ENHANCER 2: treble emphasized · Z-ENHANCER 3: bass and treble emphasized · Z-EHCR OFF: no sound effect Radio Mode Operations FM Reception ® For enhanced FM performance the tuner includes signal actuated stereo control and Multipath noise reduction circuits. * The factory default setting is "Z-EHCR OFF". Listening to the Radio 1) Press the FNC button 3 to select the radio mode, then the radio will be on. 2) To select a preset band, press the BND button @, then select one of the preset bands such as FM1, FM2, FM3, or AM. Every time the BND button @ is pressed, the display will change as: FM1 FM2 FM3 AM FM1 3) Press the SRCH Left/Right button #, then the station at which there is a broadcast will be selected (Seek selection). English Loudness Effect In order to turn on/off the loudness effect, use the LD button 2 for 2 seconds or longer. [. . . ] Press the SCN button 9 again to disengage the unit from scan play. * A scan play will start from the track following the one currently playing. Stopping (pausing) Playback Press the Play/Pause button %. Press the Play/Pause button % again to resume playback. Disc scan play Press and hold the SCN button 9 for 2 seconds or longer, then the display will show " " and "SCN", and plays the first 10 seconds of the first song of all the CDs in the CD changer. Press the SCN button 9 again to disengage the unit from disc play. English Selection of CDs Press the Direct button (1 to 6) 0 then select the CD you wish to play. * A scan play will start from the first tracks of next CDs following the one currently playing. Repeat Play Press the RPT button 8, then the display shows "RPT", then the track currently playing will be played repeatedly. Disc repeat play Press and hold the RPT button 8 for 2 seconds or longer, then the display shows both the " " and "RPT", then the disc currently being played will be played repeatedly. [. . . ]