User manual CLARION DX425

[. . . ] When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the optical parts of the player, do not use the player for about one hour and the condensation will disappear naturally to allow normal operation. Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. [. . . ] Insert the AA (UM-3/1. 5 V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover. AA (UM-3/1. 5 V) Batteries Notes: Using batteries improperly can cause them to explode. Take note of the following points: · When replacing batteries, replace both batteries with new ones. · Dispose of spent batteries properly. Rear cover Rear side 8 DX425 Functions of Remote Control Unit Buttons Mode Button & FUNC * BAND DISC UP PROG TOP ( VOLUME ) SEARCH Radio CD Turns power on and off. Top play. English Increases and decreases volume (in all modes). Switches between playback and pause. ¡ PLAY/PAUSE TM MUTE £ ISR Turns mute on and off. Press and hold for more than 2 seconds: Stores current station into ISR memory (radio mode only). Scan play. ¢ DISP SCN PS/AS § RPT BLS ¶ RDM MONI Repeat play. Random play. * Some of the corresponding buttons on the source unit and remote control unit have different functions. DX425 9 8. OPERATION Note: · Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold). Basic Operations CAUTION When this unit is turned on, starting and stopping the engine of a car with its volume raised to the maximum level may harm your hearing. · B-BOOST : bass emphasized · IMPACT : treble emphasized · EXCITE : bass and treble emphasized · CUSTOM : bass and treble adjustment · Z+ OFF : no sound effect * The factory default setting is "CUSTOM". Adjusting the Bass This adjustment can be performed when the Zenhancer Plus is set to "CUSTOM". 2) Turning Rotary knob $ clockwise emphasizes the bass; turning it counterclockwise attenuates the bass. * The factory default setting is "0". (Adjustment range: ­6 to +6) 3) When the adjustment is complete, press A button % several times until the function mode is reached. 10 DX425 Adjusting the Treble This adjustment can be performed when the Zenhancer Plus is set to "CUSTOM". 2) Turning Rotary knob $ clockwise emphasizes the treble; turning it counterclockwise attenuates the treble. Switching the Clock Display Every time the DISP button 7 is pressed, the display will change between the operation mode and the clock display. Setting the Clock 1) Press the DISP button 7 to display the clock display. 5) Press the DISP button 7, then the clock is set. * The factory default setting is "0". (Adjustment range: ­6 to +6) 3) When the adjustment is complete, press A button % several times until the function mode is reached. English Adjusting the Balance 1) Press A button % and select "BAL". 2) Turning the Rotary knob $ clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left speaker. Notes: · If · * The factory default setting is "0". (Adjustment range: L13 to R13) 3) When the adjustment is complete, press A button % several times until the function mode is reached. you select another operation mode while you are setting the clock, the clock setting operation will be canceled. If you remove the vehicle's battery for a check or repair, the clock will be reset, so you must set it again. Adjusting the Fader 1) Press A button % and select "FAD". 2) Turning the Rotary knob $ clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers. Turning the screen saver function on or off This unit is equipped with the function which enables you to display a variety of patterns and characters in the Operation status indication 2 in a random order. (Adjustment range: F12 to R12) 3) When the adjustment is complete, press A button % several times until the function mode is reached. following illustration shows one of the patterns displayed when the screen saver function is set to on. Loudness Effect In order to turn on/off the loudness effect, use the LD button % for 1 second or longer. Every time the LD button % is pressed and held for 1 second or longer, the loudness effect switches on and off. * When the loudness effect is on, the display will show "LD". DX425 11 Radio Mode Operations FM Reception ® For enhanced FM performance the tuner includes signal actuated stereo control and Multipath noise reduction circuits. Preset Memory Function Preset Memory Function can store up to 24 stations: six stations for each of FM1, FM2, FM3 and AM. Note: · When the present memory function is used, all the content of the memory will be erased. Listening to the Radio 1) Press the FUNC button 3 to select the radio mode, then the radio will be on. [. . . ] Press the RDM button 0 again to disengage the unit from disc random play. * A scan play will start from the track following the one currently playing. Disc scan play Press and hold the SCN button 5 for 1 second or longer, then the display will show DISC indication 0 and "SCN", and plays the first 10 seconds of all the tracks of all the CDs in the CD changer. Press the SCN button 5 again to disengage the unit from disc scan play. Switching magazine English This function can be used only when the connected CD changer can store a multiple number of magazines. Every time the MAG button 4 is pressed, the next magazine will be selected. Notes: · Regarding MD Changer when a MD changer is used with this unit, set the mode on the changer to "A" (CD Mode). [. . . ]