User manual CLARION DXZ555MP

[. . . ] Owner's manual Mode d'emploi Manual de instrucciones DXZ555MP CD/MP3/WMA Receiver / CeNET Control · Récepteur CD/MP3/WMA / Commande CeNET · Reproductor de discos CD/MP3/WMA con receptor y control CeNET Thank you for purchasing this Clarion product. Please read this owner's manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e. g. , glove compartment). Check the contents of the enclosed warranty card and keep it carefully with this manual. [. . . ] Turning the [ROTARY] knob clockwise emphasizes the bass; turning it counterclockwise attenuates the bass. The factory default setting is "BASS <G 0>". When the adjustment is complete, press the [A-M] button several times until the function mode is reached. DXZ555MP 13 Basic Operations Radio Operations Listening to the radio 1. Each time the button is pressed, the radio reception band changes in the following order: FM1 FM2 FM3 AM FM1. . . Press the [a, d] lever upward or downward to tune in the desired station. English Adjusting the fader 1. Turning the [ROTARY] knob clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers. The factory default setting is "FAD 0". When the adjustment is complete, press the [A-M] button several times until the function mode is reached. Tuning There are 3 types of tuning mode available, seek tuning, manual tuning and preset tuning. Adjusting MAGNA BASS EXTEND The MAGNA BASS EXTEND does not adjust the low sound area like the normal sound adjustment function, but emphasizes the deep bass sound area to provide you with a dynamic sound. The factory default setting is off. Seek tuning 1. Press the [BND] button and select the desired band (FM or AM). If "MANU" is lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available. 1. Press the [a, d] lever upward or downward to start automatic station tuning. When the lever is pressed upward, search will be performing in the direction of higher frequencies. When the lever is pressed downward, search will be performed in the direction of lower frequencies. Manual tuning There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. Press the [BND] button and select the desired band (FM or AM). If "MANU" is not lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" is lit in the display and manual tuning is now available. 2. GQuick tuning: Press the [a, d] lever upward or downward and hold in position for 1 second or longer to begin station tuning. GStep tuning: Press the [a, d] lever upward or downward to perform manual tuning. 14 DXZ555MP Radio Operations English Recalling a preset station A total of 24 preset positions (6-FM1, 6-FM2, 6FM3, 6-AM) exists to store individual radio stations in memory. Pressing the corresponding [DIRECT] button recalls the stored radio frequency automatically. Press the corresponding [DIRECT] button to recall the stored station. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store that station into preset memory. Instant station recall (ISR) Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. GRecalling a station with ISR In any mode, press the [ISR] button to turn on the radio function and tune the selected radio station. Press the [ISR] button again to return to the previous mode. Manual memory 1. Select the desired station with seek tuning, manual tuning or preset tuning. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory. Auto store Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially. [. . . ] Press the reset button for about 2 seconds with a thin rod. Reset button General CD/MP3/WMA English Nothing happens when buttons are pressed. Display is not accurate. The microprocessor has malfunctioned due to noise, etc. DCP or main unit connectors are dirty. No sound heard The speaker protection circuit is operating. Wipe the dirt off with a soft cloth moistened with cleaning alcohol. (Speaker volume is reduced automatically when the speaker protection circuit operates). [. . . ]