User manual CLARION DXZ765MP

[. . . ] Owner's manual Mode d'emploi Manual de instrucciones DXZ765MP CD/MP3/WMA RECEIVER/CeNET CONTROL RÉCEPTEUR CD/MP3/WMA : COMMANDE CeNET RECEPTOR Y REPRODUCTOR DE CD/MP3/WMA/ CONTROL DE CeNET Thank you for purchasing this Clarion product. Please read this owner's manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e. g. , glove compartment). Check the contents of the enclosed warranty card and keep it carefully with this manual. [. . . ] When the adjustment is complete, press the [A-M] button several times until the function mode is reached. Adjusting the fader 1. Turn the [ROTARY] knob to adjust the balance of the front and rear speakers. The factory default setting is "0". (Adjustment range: F12 to R12) Adjusting the subwoofer The factory default setting is "0" This function can be adjusted only when the subwoofer output is set to "ON". For details on how to set the subwoofer, refer to the subsection "Setting the subwoofer" in the section "Operations Common to Each Mode". 1. When the adjustment is complete, press the [A-M] button several times until the function mode is reached. DXZ765MP 15 Radio Operations English Listening to the radio 1. Each time the button is pressed, the radio reception band changes in the following order: F1 (FM1) F2 (FM2) F3 (FM3) A (AM) F1 (FM1). . . Press the [å, ] lever upward or downward to tune in the desired station. Recalling a preset station A total of 24 preset positions (6-FM1, 6-FM2, 6FM3, 6-AM) exists to store individual radio stations in memory. Pressing the corresponding [DIRECT] button recalls the stored radio frequency automatically. Press the corresponding [DIRECT] button to recall the stored station. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store that station into preset memory. Tuning There are 3 types of tuning modes available, seek, manual and preset tuning. Manual memory 1. Select the desired station with seek tuning, manual tuning or preset tuning. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory. Seek tuning 1. Press the [BND] button and select the desired band (FM or AM). If "MANU" is lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available. Auto store Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially. If 6 receivable stations cannot be received, a previously stored station remains unoverwritten at the memory position. The stations with good reception are stored automatically to the preset channels. 2. Press the [å, ] lever upward or downward to start automatic station tuning. When the lever is moved up, the station is sought in the direction of higher frequencies; if the lever is moved down, the station is sought in the direction of lower frequencies. Manual tuning There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. Press the [BND] button and select the desired band (FM or AM). If "MANU" is not lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" is lit in the display and manual tuning is now available. Preset scan Preset scan receives the stations stored in preset memory in order. This function is useful when searching for a desired station in memory. When a desired station is tuned in, press the [ ] button again to continue receiving that station. [. . . ] Consult Clarion dealer. English Amplifier turn-on lead is Turn the unit off and check each wire for a possible shorted to ground or short. If the amplifier turn-on lead shorts out, cover it excessive current is required. Turn off the power, then press the [RELEASE] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod. Reset button General Display is not accurate. [. . . ]