User manual CLARION M202RC-RET

[. . . ] Two M202RC-RET units may be used with a single M335-RET (using an optional M101RYC adapter). The M202RC-RET can be connected to your boat's illumination circuit, backlighting the panel in low-light conditions. 2. CARE AND MAINTENANCE Clean the remote control panel with a slightly damp, soft cloth using household glass cleaner. Do not use solvents such as benzene, thinner, or commercially available cleaners. [. . . ] Before you begin installation of the panel, verify that you have sufficient clearance in the desired location. A flat surface is required in order to ensure a watertight seal when mounting is complete. Before cutting any panel, ALWAYS ensure that there is sufficient clearance behind the panel, and that no wire harnesses, fuel lines, moving linkages, or any other critical components are exposed to damage by your choice of location. Owner's Manual / Installation Guide (1) Prepare the boat for installation by carefully removing interior trim panels as necessary. Route wire harnesses away from sharp edges, and ensure that no harnesses will be pinched or pierced during reassembly. M202RC-RET 7 1. Determine the mounting location is a flat surface with sufficient rear clearance (2. 5") and access. Ensure that the installation can be successfully completed before continuing!If the cable is not long enough, a cable extension is available - P/N M101RXC. The remote control panel requires a 2" (51mm) diameter round hole. The mounting bracket is scored with "break lines' to allow use with panels of different thicknesses. Determine if the bracket needs to be shortened, and remove the appropriate number of breakaway segments using a pair of pliers. Each segment is 1/4" long. 2. Mounting Bracket 2" (51mm) Diameter Hole Break Lines 4. VO VO LU ME LU ME Insert the remote control panel into the opening. Make sure that the gasket behind the remote control panel face seats completely against the mounting surface. BA ND SO UR PO CE WER MUT E SE SE LE CT LE CT 8 M202RC-RET 5. Position the bracket onto the rear of the remote control panel, sliding the two threaded studs on the rear of the panel through the two holes in the mounting bracket (as shown below). Tighten the 7mm hex nuts onto the bracket, again ensuring that the gasket seals tightly to the front of the mounting surface. Avoid pinching the cable. Wiring Connections Take the following precautions before wiring your system. · · Disconnect the negative battery terminal before making any wiring connections. Sharp edges can pierce wire insulation and cable jackets, causing short circuits, damage to the craft, blown fuses, and system failure. If any fuse should blow, make sure all connections are correct and no wires are damaged before replacing the fuse. When replacing a fuse, never let the battery side touch any metal part or any other wire. · Wiring 1. Connect a wire to one of the mounting studs on the rear of the unit, using a #8 ring terminal (not supplied). Connect this wire to the boat's negative (-) ground. M202RC-RET 9 2. The illumination circuit of the M202RC-RET operates with a 12V(+) input. Wire with a . 250 female insulated spade terminal (not supplied), and connect the illumination terminal on the rear of the panel to a 0. 5A in-line fuse (not supplied). Connect the other side of the fuse to an illumination circuit of the boat. 3. [. . . ] ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES SHALL CLARION BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT. BECAUSE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. [. . . ]