User manual CLARION MSS430

[. . . ] · Use extreme caution when drilling around electrical wiring, brake lines, and fuel lines. Check clearances on both sides of a planned installation surface before drilling any holes or installing any screws. · Always wear protective eyewear when using tools. · Use only high-quality RCA cables that are no longer than necessary for direct connections to other components in the system. [. . . ] Use these jacks to connect a second video source (e. g. , video game console, TV Tuner, etc. ) OWNER'S MANUAL/INSTALLATION GUIDE 3 A/V INPUT 3 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a third video source. 5 POWER INPUT CONNECTOR (4-Pin Molex) Connect the enclosed Molex pigtail to the vehicle's power, ground, and back-up light circuits, (see Figure 3 on page 6). 4 A/V INPUT 4 (3 -RCA Jacks) Same as A/V Input 1. NOTE: When using a optional Clarion Rear Vision Camera, the video connection must be connected to A/V Input 4 to function properly with the reverse wire. When +12Vdc is applied to the reverse wire (Pin 4), the MSS430 will automatically override Control Station 1's video selection and switch directly to A/V Input 4. The LED indicator will blink to show that the reverse function is active. The video signal will automatically override any other selection that is being viewed on Monitor 1. When voltage is removed from the reverse wire, the monitor will automatically switch back to the original source selected. 11 SOURCE COMMANDER MSS430 DESCRIPTION OF MSS430 REAR CONNECTORS (CONT'D) 6 7 8 9 0 q w e r Figure 11. The MSS430's A/V Outputs and Power connectors. 6 CONTROL STATION 1 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 1 audio/video sources. The Control Station connected to this port provides control and selection of Zone 3 audio/video sources. 9 A/V OUTPUT 1 (3 -RCA Jacks) Use this output when connecting the MSS430 to an external (NTSC-composite type) video monitor for Zone 1. 7 CONTROL STATION 2 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 2 audio/video sources. 0 MONITOR 1 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 1. 8 CONTROL STATION 3 (6 -Pin Connector) 12 OWNER'S MANUAL/INSTALLATION GUIDE q A/V OUTPUT 2 (3 -RCA Jacks) Use this output when connecting the MSS430 to an external (NTSC-composite type) video monitor for Zone 2. DESCRIPTION OF CONTROL STATION 1 w MONITOR 2 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 2. e A/V OUTPUT 3 (3 -RCA Jacks) Use this output when connecting the MSS430 to an external (NTSC-composite type) video monitor for Zone 3. 4 2 3 Figure 12. The Control Station's Power button, source LED indicators, and Source Select buttons. r MONITOR 3 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 3. 1 SOURCE SELECT LEDs When illuminated, each LED indicates which A/V source is selected. Press the SOURCE SELECT button to change source selection and the corresponding LED will illuminate. 13 SOURCE COMMANDER MSS430 2 SOURCE SELECT Button Press the SOURCE SELECT button one or more times to step through the different Audio/Video inputs. Press and hold the Power button for 2 to 3 seconds to power down the monitor at each of the Control Stations. 4 Mounting Bezel Outer mounting bezel around each Control Station allows for easy installation. (see page 6 for intallation information). 3 POWER Button When ignition is applied to the MSS430's ignition lead, all control stations are automatically set into the Stand-By mode (no power output from the monitor's power connector). Press the POWER button on any Control Station and the source LED will illuminate and the monitor will power on. NOTE: Control Stations a). If the Ignition is shuts down while the Control Stations are in use, the Control Stations will not automatically turn on when the ignition is activated again. [. . . ] vehicle is in reverse gear. 19 SOURCE COMMANDER MSS430 MSS430 SPECIFICATIONS Audio Specifications Maximum Output: Frequency Response: S/N Ratio (A-wtd): Input Sensitivity: Input Impedance: Input/Output Gain: Video Specifications ­ 4 Vp-p (peak to peak) 30 Hz to 25 kHz 60 dB 1. 0 Vp-p (peak to peak) 10k Ohms 0dB +/-2dB at Max volume with 600 Ohm load. 1. 0 Vp-p +/- 20% (peak to peak) 39 Hz to 5. 5 MHz 0dB +/-2dB with 75 Ohm load 0Vp-p +/- 20% (peak to peak) 75 Ohms 10 Vd c - 13 Vd c 1. 6 A Dimensions (w x h x d): 9. 84 x 1. 06 x 5. 24 in. (250 x 27 x 133 mm) CONTROL SPECIFICATIONS Dimensions (w x h x d): 1. 7 x 2. 6 x . 60 in. [. . . ]