User manual CLARION RDX555D

[. . . ] When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the optical parts of the player, do not use the player for about one hour and the condensation will disappear naturally to allow normal operation. Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. [. . . ] <Fader adjustment> : The volume of the front speakers are increased. : The volume of the rear speakers are increased. Turning ON the Power and Adjusting the Volume 1) Press the POWER button 3 . 3 for 1 second or longer. 2) Press the FNC button 3 and select another English * To turn off the power, press the POWER button Setting the Z-enhancer This unit comes with three types of sound tone effects stored in memory. Every time the FNC button 3 is pressed, the display changes the operation mode as: Radio § CD § CD changer § MD changer § Radio * The factory default setting is "Z-EHCR OFF". Each time you press Z-EHCR button 8 , the tone effect changes in the following order. "Z-ENHANCER 1" § "Z-ENHANCER 2" § "Z-ENHANCER 3" § "Z-EHCR OFF" § "Z-ENHANCER 1". . . · Z-ENHANCER 1: bass emphasized · Z-ENHANCER 2: treble emphasized · Z-ENHANCER 3: bass and treble emphasized · Z-EHCR OFF: no sound effect Notes: · The operation mode not connected to the unit will not be selected. · If the CD mode is selected when no disc is inserted, the display flashes " DISC" and the mode will be switched to the radio mode instead. 3) Adjust the volume by pressing the Up/Down button 2 . : Sets the volume down. Loudness Effect In order to turn on/off the loudness effect, use the LD button 17 for 2 seconds or longer. Every time the LD button 17 is pressed and held for 2 seconds or longer, the loudness effect switches on and off. Audio Mode Adjustments 1) Press the A-M button 17 and select the mode you want to adjust. Every time the A-M button 17 is pressed, the display changes as: BASS/TRE § BAL/FAD § originally selected mode 2) After selecting a mode, adjust the mode by using either the Left/Right button 18 , or the Up/Down button 2 . : Decreases the treble. * When the loudness effect is on, the display will show "LOUD. " Switching the Clock Display While pressing the BND button 16 , every time the DISP button 12 is pressed, the display will change between the operation mode and the clock display. Setting the Clock 1) While pressing the BND button 16 , press the DISP button 12 to display the clock display. 2) While pressing the BND button 16 , press and hold the DISP button 12 for 2 seconds or longer. 3) Press the Left button 18 , then set the current hour. 9 4) Press the Right button 18 , then set the current minute. 5) Press the BND button 16 , then the clock is set. Radio Mode Operations FM Reception ® For enhanced FM performance the tuner includes signal actuated stereo control and Multipath noise reduction circuits. Notes: · If · you select another operation mode while you are setting the clock, the clock setting operation will be canceled. If you remove the vehicle's battery for a check or repair, the clock will be reset, so you must set it again. Listening to the Radio 1) Press the FNC button 3 to select the radio mode, then the radio will be on. 2) To select a preset band, press the BND button 16 , then select one of the preset bands such as FM1, FM2, FM3, or AM. Every time the BND button 16 is pressed, the display will change as: FM1 § FM2 § FM3 § AM § FM1 3) Press the Left/Right button 18 , then the station at which there is a broadcast will be selected (Seek selection). English 10 Manual Tuning 1) Press the BND button 16 , then select FM1, FM2, FM3 or AM. 2) Press and hold the BND button 16 for 2 seconds or longer, then the display will show "MANU, " which means that a manual selection function is on. 3) Press the Left/Right button 18 and select the right station. Seek Tuning 1) Press the BND button 16 , then select FM1, FM2, FM3 or AM. 2) If the "MANU" on the display is on, press and hold the BND button 16 for 2 seconds or longer. When the "MANU" display is off, the Seek Selection function is on. 3) Press the Left/Right button 18 , then when it selects the station in which there is a broadcast, it automatically stops. Preset Memory Function Preset Memory Function can store up to 24 stations: six stations for each of FM1, FM2, FM3 and AM. Note: · When the present memory function is used, all the content of the memory will be erased. Manual memory function 1) Press the BND button 16 , and select the band you want to store in the memory. 2) Press the Left/Right button 18 then select the station you want to store in the memory. [. . . ] At that time, the new magazine will be locked. Selection of MDs Press the DISC Up button 5 or the DISC Down button 6 , then select the MD you wish to play. UP: Every time you press the button, the MDs will be selected as: 1 § 2 § 3 § 4 § 5 § 6 § 1. . . . DN: Every time you press the button, the MDs will be selected as: 1 § 6 § 5 § 4 § 3 § 2 § 1. . . . . Note: · While the magazine lock function is on, the Scan Play function or Random Play function will be performed among the locked magazines. Top Function Press the TOP button 10 , then the MD will start playing from the first song (track number. : Playback will start from the beginning of the track currently playing. [. . . ]