User manual CLARION TB743W

[. . . ] English Owner's manual & Installation manual Owner's manual IN-DASH WIDE 7" COLOR LCD TV Thank you for purchasing the Clarion TB741P/TB742P/TB743W. * Please read this Owner's manual & Installation manual in its entirety before proceeding with wire connection and installation. * After reading this manual, be sure to keep it in a handy place (e. g. , glove compartment). English Owner's manual I Contents · Owner's manual 1. CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press and hold the [OPEN/CLOSE] button when the liquid crystal panel is upright, and release the button when a beep is heard. The liquid crystal panel turns horizontal. Press the [OPEN/CLOSE] button again when the liquid crystal panel is in the horizontal position, and the panel returns to the original position. Even if the button is not operated for about 10 seconds, the panel returns to the original position with a warning sound. TB741P/TB742P/TB743W 11 Basic Operations Selecting the screen size Four screen display modes are supported: normal, wide, full wide and cinema. Note: · The screen mode cannot be selected while the vehicle is in motion. Note: · When the wide mode or full wide mode is used to display a normal 4:3 picture which is not a wide picture so that it fills the whole wide TV screen, parts of the picture around the edges will be off the screen or the picture will be distorted on the screen. To view original pictures so as to respect the intentions of the producer, use the normal mode. English Owner's manual Press the [DISP] button for 1 second or longer to select the screen display mode. Each time this button is pressed for 1 second or longer, the display mode is changed in the sequence shown below. I For normal 4:3 picture reception Depending on which mode is set, the shape of the picture will be distorted on the screen. G Full wide mode G Cinema mode 62 TV1 F. WIDE 62 TV1 CINEMA The whole picture is stretched in the sideways direction. The picture at the top and bottom of the screen is off the screen. G Wide mode G Normal mode (normal screen) 62 62 TV1 WIDE TV1 NORMAL The picture at the left and right of the screen is stretched in the sideways direction. In wide mode, the picture is stretched in both the upward and downward direction when a PAL signal is received. Black bands appear to the left and right of the screen. I For wide (16:9) picture reception Use the cinema mode. G Normal mode G Cinema mode 62 62 Wide mode, full wide TV1 NORMAL TV1 CINEMA Black bands appear all around the screen. The picture is shown expanded so that it fills the whole screen. 12 TB741P/TB742P/TB743W TV Mode Operations CAUTION For your safety, the driver should not watch the TV or operate the controls while driving. Please note that watching and operating the TV while driving is prohibited by law in some countries. Also, while driving, keep the volume to a level at which external sounds can be heard. English Auto store function The channels received automatically are automatically stored in the preset channels. The setting procedure for the preset channels is the same for TV1 and TV2. Press the [PS] button for 1 second or longer, the broadcast stations are automatically stored in the memory starting with the one following the station now received. TV1 1 2 3 4 5 6 F. WIDE Owner's manual Watching TV 1. Each time the [BND] button is pressed, the setting is switched in the sequence shown below. TV1 TV2 VTR1 VTR2 A. STORE 62 Seek tuning Keep pressing the [a] or [d] button for about 1 second. Tuning will stop automatically at a channel where a broadcast is received. When seek tuning has stopped before or after a broadcast channel, press the [a] or [d] button again. Notes: · The signal conditions are sometimes such that a channel without a station is stored in the memory. · Some stations may not be stored if their signals are too weak in the reception area. · When a station could not be stored or a channel without a station has been stored in the memory, refer to the section on the manual memory function which follows, and perform the settings again. Manual memory function 1. Press the [MEMO] button, the manual memory screen is displayed. While the channel display at the left of the screen turns red, the manual memory operation is available. Manual tuning Press the [a] or [d] button to select the channel. The channel number appears at the top right of the screen. Each time the [a] or [d] button is pressed, the channel number is incremented or decremented by 1. The channel number remains on the screen for about 5 seconds. Preset memory function The number of preset channels which can be stored in the memory is: · 6 stations for TV1 · 6 stations for TV2 Total of 12 stations Any station can be stored in any preset channel. } 3. Press the [w] or [z] button to select the preset channel in which the station to be stored. Press the [MEMO] button for 1 second or longer to store the station into the preset memory. To cancel the manual memory mode, press the [MEMO] button again and press the [DISP] button. Note: · The memory contents are returned to the default settings when the battery is replaced or the power supply is otherwise suspended. TB741P/TB742P/TB743W 13 TV Mode Operations Preset scanning 1. [. . . ] #: The parts and screws with this mark are originally attached to the vehicle. Figure 8 Note 1: In some cases, the center panel may require some modification (trimming, filling, etc. ). Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool. 24 TB741P/TB742P/TB743W 6. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. Insert the hook plate between the spring and the universal mounting bracket, fit tab B of the spring into hole A of the hook plate, Universal mounting bracket 2­Hook plates English Installation and Wire connection manual then pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate. ) (Figure 9) Note: Keep the hook plate. [. . . ]