User manual CLARION VRX918R

[. . . ] 2 Cord clamp Spacer Special screw 9 Bag for accessories of tuner amp unit Maunting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote control unit @ Battery (for remote control unit) # Outer Escutcheon $ DCP Case VRX918R 53 3. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service centre. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently. English Installation and Wire connection manual 4. [. . . ] This model is used with the LCD panel slid forwards (shell loading system). On some types of cars, the LCD panel may touch the dashboard or shift lever, in which case it cannot be installed. Check that the set will not hamper operation of the shift lever before choosing the place of installation. (Figure 2) Dashboard 5. The source unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles. T N T Shift lever (check that it does not touch the LCD. ) Shift lever Figure 2 3. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 54 VRX918R 5. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. Insert the main unit into the universal mounting bracket until it locks. Mount the outer escutcheon so that all the hooks are locked. English Installation and Wire connection manual Notes: 1) Some car models require special mounting kits for proper installation. 2) Fasten the front stopper securely to prevent the main unit from coming loose. • Console opening dimensions 182 mm Rear fastening hole (of vehicle) Hole 53 mm Instrument panel Hole Stoppers Screwdriver Rubber cap Main unit Universal mounting bracket Stoppers 2-Spring Outer escutcheon Note: Set the outer escutcheon so that its metallic part on the back side fits the upper edge of the main unit. Figure 6 VRX918R 55 s Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) English Installation and Wire connection manual This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (∗). ∗2: In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory <<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory. ∗3: Connecting the PHONE MUTE Terminal The lead included with the unit must be connected to the specified position of the vehicle’s ISO connector in order to use the “triggered audio mute for cellular telephones” function. (Provided with this unit) Note : Before making any installation, disconnect the car battery - (negative) cable. ∗5: When connecting a DSP (sold separately), set the normal DSP select switch to “D”. Then, the AUDIO OUT (IN) terminal of the Tuner Amp Unit is only available for audio input, not outputting D the audio. N ∗6: ∗7: ∗8: ∗9: Connect to a separately sold external antenna, DSP, etc. Connect to a separately sold navigation device. VRX918R 59 s Connecting the Accessories • Connection to the external amplifier The external amplifier cannot be connected unless the DSP is connected. For detailed information, refer to the instruction manual of the DSP. English Installation and Wire connection manual • Connection to the security camera for vehicle The rear vision camera for vehicle can be connected to the system expansion terminal on the main unit. For detailed information, refer to the instruction sheet or manual for the rear vision camera. Notes: • A power supply box (sold separately) is required for connection of the main unit and the security camera. [. . . ] • While the CCD camera is used, the navigation cannot be turned on. Please use the CCA188 instead. • If the specified lead of the cellular phone is connected to the phone mute lead of the source unit, the audio mute is available when the cellular telephone is used. For audio mute setting in cellular telephone use, see page 40. • DAB (Digital Audio Broadcasting) When the DAB is to be connected, use the CeNET connector. The DAH9500Z cannot be connected. • TV Tunner When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For detailed information, refer to the instruction manual of the TV TUNER. s Connecting the parking brake lead Connect the lead to parking brake lamp earth in the meter panel. Notes: • Connecting the parking brake lead to lamp earth allows you to watch TV/VTR/DVD VIDEO when the parking brake is engaged. [. . . ]