User manual CLARION XA311

[. . . ] Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas. 3. Remove tape slack before inserting a cassette, particularly when using C-90 or prerecorded cassettes. Avoid using C-120 or longer cassettes (The very thin tape may stretch or break). Exposure to direct sunlight, extreme temperatures or high humidity may damage cassettes. SOURCE UNIT / APPAREIL PILOTE / UNIDAD FUENTE 1 2 3 4 5 67 8 9 Ranura de inserción de casete 0 ! [. . . ] · Z-ENHANCER 1 : bass emphasized · Z-ENHANCER 2 : treble emphasized · Z-ENHANCER 3 : bass and treble emphasized · OFF : no sound effect * The factory default setting is "0". When the adjustment is complete, press A-M button 4 several times until the function mode is reached. 6 XA311 Basic Operation Adjusting the fader 1. Turning the Rotary knob 3 clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers. Tape Operation Loading Tapes Insert the cassette tape into the Cassette insertion slot with the side on which the tape is exposed facing the right. Playback starts automatically. * When * The factory default setting is "0". (Adjustment range: F9 to R9) the end of the cassette tape is reached, the auto reverse mechanism is activated and the other side of the tape begins playing automatically. English 3. When the adjustment is complete, press A-M button 4 several times until the function mode is reached. Note: · Fully insert the cassette tape into the cassette insertion slot. Switching the Display While pressing the BAND button 6, press the DISP button $ to enter the clock display mode. Main display § Clock display § Main display Listening to a tape which is already loaded Press the FUNC button 5 to select the tape mode. Playback begins automatically. Ejecting Cassette Tapes Press the Eject button 9. The cassette tape is ejected. Setting the Clock 1) While pressing the BAND button 6, press the DISP button $ to enter the clock display mode. 2) While pressing the BAND button 6, press and hold the DISP button $ for 2 seconds or more. This enables the clock editing mode. * The radio mode is selected automatically 4 seconds after ejecting the tape. Fast-Forwarding and Rewinding Use the FF button @ and REW buttons 0. : Press this to rewind the tape. * The editable fields will be indicated when the display flashes. 3) To move between the hour and minute fields, use the Up (hour) and Down (minute) buttons 1. 4) To store the clock setting, press the BAND button 6. * It is possible to listen to the radio during fast-forward, rewind or search operations. Switching to the Other Side of the Tape Press the PROG button !Playback is switched automatically to the other side of the cassette tape. Notes: · If you select another operation mode before complet· ing the above procedure, the clock setting operation will be canceled. Removing the vehicle's battery for a check or repair will cause the clock to reset to 1:00. Set the clock again if this happens. XA311 7 Radio Operation FM Reception For enhanced FM performance the ® tuner includes signal actuated stereo control and Multipath noise reduction circuits. Presetting Stations A total of 25 stations can be preset, 5 each for the FM1, FM2, FM3, FM4 and AM bands. Note: · When a station is preset, the station previously stored Listening to the Radio 1) Press the FUNC button 5 to select the radio mode. 2) To tune to a desired preset station, first press the BAND button 6 and select FM1, FM2, FM3, FM4 or AM. The band changes as follows each time the BAND button is pressed: FM1 § FM2 § FM3 § FM4 § AM § FM1 3) Use the corresponding Preset buttons * to select the desired station. in the memory at that position is cleared. Seek Tuning 1) Press the BAND button 6 and select the desired band. 2) Press the Up or Down buttons 1 to seek up or down the frequency band. Seek tuning automatically stops when a station is found. Presetting stations manually 1) Press the BAND button 6 to select the band at which to store the station. 3) Press and hold the corresponding Preset button * for at least 2 seconds to store the station into memory. Auto store function (Automatic Station Store) 1) Press the BAND button 6 to select the band at which to store the stations. [. . . ] When sound is muted again, check the unit with a wire connected last. Connections are improper. Sound quality is poor. Playback head is dirty. English No sound while unit can be operated. Power ANT lead is shorted to the ground. 7. ERROR DISPLAYS s To protect the system, this unit has been equipped with self diagnostic functions. Error Display Corrective Measure This error display indicates that a fault has arisen in the mechanism of the source unit or CD changer (for example, the disc cannot be changed or ejected). This error display indicates that the pickup focus is off because of a scratched disc or some other factor during source unit or CD changer play. [. . . ]