User manual COMPX SW2-1138AD

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual COMPX SW2-1138AD. We hope that this COMPX SW2-1138AD user guide will be useful to you.


COMPX SW2-1138AD : Download the complete user guide (159 Ko)

Manual abstract: user guide COMPX SW2-1138AD

Detailed instructions for use are in the User's Guide.

[. . . ] As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc. It is advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, fireplaces, stoves, etc. Fitting the appliance Gas and mixed hobs are manufactured with type X degree protection against overheating. The following precautions must be taken when installing the hob: • Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from the edge of the hob. [. . . ] Adjacent Room Room to be Vented • The installation cavity should have the dimensions indicated in the figure. This must be placed at a minimum distance of 20 mm from the lower part of the hob. Ventilation To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams). When installing the cooktop above a built-in oven without forced ventilation, ensure that there are air inlets and outlets for ventilating the interior of the cabinet adequately. Gas connection The appliance should be connected to the main gas supply or to a gas cylinder in compliance with current national regulations. Before carrying out the connection, make sure the cooker is compatible with the gas supply you wish to use. If this is not the case, follow the instructions indicated in the paragraph “Adapting to different types of gas. € When using liquid gas from a cylinder, install a pressure regulator which complies with current national regulations. Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. 78 MJ/m³ A R S S RR A TC S R A Ø145 S 7HPC 640 /HA 7HPC 640 X/HA 7HPC 640 GH/HA 7HPC 640N /HA 7HPC 640N GH/HA 7HPC 640N X /HA PC 640N /HA PC 640N X/HA GPC 64 R GH RU/HA GPC 64 R GH RU/HA GPC 64 N X RU/HA GPC 64 N GH RU/HA GPC 64 N RU/HA 7HPC 631 /HA 7HPC 640 T GH /HA 7HPC 631 X/HA 7HPC 640 T R /HA 7HPC 640 T X /HA GPC 64 T R GH RU/HA GPC 64 T R GH RU/HA DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 5 Description of the appliance GB Overall view GAS BURNERS Support Grid for COOKWARE Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. • GAS BURNER ignition* enables a specific burner to be lit automatically. € SAFETY DEVICE* stops the gas flow if the flame is accidentally extinguished. The position of the corresponding gas burner or electric hotplate* is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: • Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. [. . . ] € Always make sure that pan handles are turned towards the centre of the hob in order to avoid accidental burns. € Do not close the glass cover (if present) when the gas burners or electric hotplates are still hot. Disposal • When disposing of packaging material: observe local legislation so that the packaging may be reused. € The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE COMPX SW2-1138AD




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual COMPX SW2-1138AD will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.