User manual CURTIS IP200

[. . . ] Install 3pcs AA batteries (Not Included) or DC adapter (Not Included), then press and hold [UP] and [DOWN] button for six seconds until the LCD display Adjust Contrast to enter the setting manual including LCD Contrast Adjustment, Language Selectable, Area Code Setting and Time/Date Setting: A. LCD Contrast Adjustment - When Adjust Contrast display on LCD, use [v] and [w] to select the contrast level. - Press [DEL] to confirm Language Selectable - After LCD contrast adjustment, the LCD will display ENG, ESP, FRA (ENG=English, ESP=Spanish, FRA=French), use [v] and [w] to select the desire language mode. [. . . ] - Press [DEL] to confirm Area Code Setting - After language setting, the LCD will display ENTER AREA CODE, use [v] and [w] to set the first digit of area code. - Press [DEL] to confirm - Use the same method to set the rest of digits. Time/Date Setting - After area code setting, the LCD will display ENTER TIME DATE, use [v] and [w] to set time. - Press [DEL] to confirm - Use the same method to set Date B. C. D. Note: If you want to reset the Press and hold [v] and [w] and [DEL] for six seconds at the same time, all of the present setting will be cleaned. DESCRIPTION OF DISPLAYING A. 3 line LCD displaying, upper line displays the basic information, middle line displays the number of in-coming call and bottom line displays the name of caller · "NEW" appears when there are new incoming calls · "CALL #" means the total amount of incoming calls · "RPT#" means the total amount of repeated incoming calls · "XX:XX AM/PM XX/XX" means Hour:Minute Morning/Afternoon Month/Day respectively · "MGS" means Message B. If a number was received more than once, the LCD will only display the time and date of the last call when review the incoming calls. If the time and date of incoming call is different from the Telephone Company, the telephone will adjust the time and date automatically according to Telecom Provider when receiving calls. If there is no operation or no incoming calls more than 30 seconds, LCD only displays time and date, total amount of received calls and amount of new incoming calls E. Ringer LED will light when there is a new call coming in until any functional keys be pressed. To get a new dial tone press the HOOK SWITCH or hang up the phone for 2 seconds. Flash Time Selectable When in an office equipped with PABX, your unit makes it easy to transfer calls. When the party answers, announce the call and hang up If you receive a busy or no answer: Press and release FLASH button to re-connect to calling party. You may select the flash time by following steps: - Under on-hook or off-hook state, Press [STORE] and [FLASH] key at the same time. - The LCD will display 'FLASH', press the number among 0-9 to select the flash time: 1: 100ms 7: 700ms 2: 200ms 8: 800ms 3: 300ms 9: 900ms 4: 400ms 5:500ms 0: 1200ms 6: 600ms Mute Function Holding down the 'MUTE' button prevents the other party from hearing your conversation with other people on your side until the button is released. To Store 3 One-Touch (M1/M2/M3) Dialing Memories Get the dial tone Press [STORE] button Enter the number you want to store Press the desire one-touch button (M1/M2/M3) Get the dial tone Press [STORE] button Enter the number you want to store Press [AUTO] button Press the desire location among the digit 0-9 To Store 10 Two-Touch Dialing Memories To Dial 3 One-Touch (M1/M2/M3) Dialing Memories - Get the dial tone - Press M1/M2/M3 (the location which was stored) to dial out the number To Dial 10 Two-Touch Dialing Memories - Get the dial tone - Press [AUTO] button - Press the digit among 0-9 (the location which was stored) to dial out the number IMPORTANT NOTES To operate the unit, you must have 'CALLER ID SERVICE' setup with your local telephone company. Some functions such as 'CALLER NAME INDICATION' will only operate if such services are included in the user's Caller I. D. Speakerphone IMPORTANT SAFETY INSTRUCTIONS When you use this telephone, follow these safety precautions to reduce the risk of fire, electric shock and injury. - Read and understand all instructions - Unplug the phone from the wall jack before cleaning with a damp cloth - Do not use liquid or aerosol cleanser. Do not use this phone near water for example, near a bath tub, sink, or pool - To reduce the risk of electric shock, do not push objects through the phone's slot or disassemble the phone. Pushing objects in the phone or opening or removing covers might expose you to dangerous voltages or other risk. [. . . ] Pushing objects in the phone or opening or removing covers might expose you to dangerous voltages or other risk. Incorrect reassemble can cause electric shock when you use the telephone - Do not place the phone on a bed, rug, and any similar surface or near a heater. The phone has slots and openings for ventilation that must not be blocked or covered. [. . . ]