User manual CURTIS MWC495

[. . . ] Run the AC power cord down through the provided cable channel for flush wall mounting. Slip the telephone base onto the wall, lining up the wall mounting holes over the screws. Finish installation by following steps TELEPHONE OPERATION SET KEY SETTING (for area number/local number/time/date/alarm setting) While continuously holding down the hook switch or when the telephone line cord is disconnected. Press<SET> key to enter the setting mode One time- To enter area number Two times- To enter local number setting Three times- To enter data/time setting (only selectable for 12 hour format with AM & PM indicator). [. . . ] Enter into Date & Time setting mode (Press <SET> button, three times for setting the date and time, Press Review Left Up[ ] Key to change content, Review Right Down[ ] Key - to change site) Enter your desired date by directly pressing the Digital key (0-9) directly for setting the 2. 3. (For example: Dec, 25th, press "1" "2" for the month, and "2" "5" for the date/ for Feb, 2nd, press "2" for the month and "2" for the date. ) Enter your desired time by directly pressing the Digital key (0 -9) directly date. (only 12 hours format/ Setting range: Hour: 00- 12; Minute: 00-59) For example: 3:25pm, press "1" "5" for hour, and "2" "5" for minute. And the "pm" will show on the display as "pm 3:25", For 4:00am, press "4" for the hour, and "0" "0" for the minute. And the "am" will show on the display as "am 4:00" TONE/PULSE (T/P) SWITCH 1. Set the Tone/Pulse Switch on the side of the handset to TONE position if Tone dialing is offered in your area. If you are not sure what service you have, set the switch to tone, and if the phone doesn't work, try Pulse. Set the switch to the PULSE position only if Pulse (rotary) dialing service is the only service available in the your area. VOLUME HI/LOW (FOR THE HANDSET) Use the Volume High/Low Switch on the side of the handset to choose between the desired handset receiver volume (High or Low). RINGER HIGH/LOW SWITCH Use the Ringer High/Low Switch on the left side of the base to choose between the desired ringer volume (High or Low). BASIC TELEPHONE OPERATION Making a call 1. When you hear the dial tone, dial the telephone number for the party you wish to reach. After several seconds the call timer will begin keeping track of the elapsed time for the phone call. To hang up, place the handset back in the base. Last number redial 1. After several seconds the call timer will begin keeping track of the elapsed time for the phone call. To hang up, place the handset back in the base. Receiving calls 1. press this button simultaneously with the HOUR or MINUTE button to set the desired time. Use these buttons to set the time, while pressing the Alarm set button or Sleep button. slide the switch to turn radio "ON", "OFF" or to "AUTO" position. When the switch is in the "AUTO" position, it will permit automatic turning "ON" and "OFF" of the radio according to the sleep and alarm settings. Press this button simultaneously with the HOPUR or MINUTE button to set the desired wakeup time. Press this button to display the number of minutes (59 or less) where the radio will sound for 59 minutes and will automatically turn off after then. When you are awakened by music or buzzer but wish to sleep a few to sleep a few minutes more, simply touch the "snooze" button and it will shut off the music or buzzer for approximately 5 to 10 minutes before the music or buzzer sounds again. To turn the radio off adjust the Radio On/OFF/Auto switch to "off" RADIO SPEAKER ON/OFF BUTTON During the radio was in using mode. The radio will being in using mode again. TO SET THE TIME Step 1--- Press the Time set button together with the HOUR or MINUTE button to set the correct time. A glowing dot appears in the lower left hand corner of the display, indicating that the time shown is PM time. TO SET THE ALARM Step 1--- Press the Alarm set button to check the alarm time. Step 2---Press the Alarm set button together with the HOUR or MINUTE button to adjust the alarm time, paying close attention on the PM indicator. [. . . ] Step 2 ---Turn the radio on and select the desired radio station and volume setting as previously instructed. Your unit is now set to turn on automatically at the pre-selected alarm time. TO WAKE BY BUZZER Step 1-- Follow step 1 to step 3 under "TO WAKE TO RADIO". Step 2--- Rotate the VOLUME/BUZZER switch to the "BUZZER" position. You will be awakened at the pre-selected alarm time by the buzzer tone. [. . . ]